| Commit message (Collapse) | Author | Age |
|---|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This test was added, commented out, in fed1b5ca (git-checkout: Test
for relative path use, 2007-11-09). Later git's path handling was
improved (d089ebaa, setup: sanitize absolute and funny paths in
get_pathspec(), 2008-01-28) but we forgot to enable the now-working
test.
This test expects to run from a subdirectory, so add a 'cd'. While
we're here, examine the content of the checked-out file instead of
just checking that it exists. The other checkout tests already do the
same.
Signed-off-by: Stefan Beller <stefanbeller@googlemail.com>
Signed-off-by: Jonathan Nieder <jrnieder@gmail.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
When we expect a git command to notice and signal errors, we
carelessly wrote in our tests:
test_expect_success 'reject bogus request' '
do something &&
do something else &&
! git command
'
but a non-zero exit could come from the "git command" segfaulting.
A new helper function "tset_must_fail" is introduced and it is
meant to be used to make sure the command gracefully fails (iow,
dying and exiting with non zero status is counted as a failure
to "gracefully fail"). The above example should be written as:
test_expect_success 'reject bogus request' '
do something &&
do something else &&
test_must_fail git command
'
Signed-off-by: Junio C Hamano <gitster@pobox.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Originally, test_expect_failure was designed to be the opposite
of test_expect_success, but this was a bad decision. Most tests
run a series of commands that leads to the single command that
needs to be tested, like this:
test_expect_{success,failure} 'test title' '
setup1 &&
setup2 &&
setup3 &&
what is to be tested
'
And expecting a failure exit from the whole sequence misses the
point of writing tests. Your setup$N that are supposed to
succeed may have failed without even reaching what you are
trying to test. The only valid use of test_expect_failure is to
check a trivial single command that is expected to fail, which
is a minority in tests of Porcelain-ish commands.
This large-ish patch rewrites all uses of test_expect_failure to
use test_expect_success and rewrites the condition of what is
tested, like this:
test_expect_success 'test title' '
setup1 &&
setup2 &&
setup3 &&
! this command should fail
'
test_expect_failure is redefined to serve as a reminder that
that test *should* succeed but due to a known breakage in git it
currently does not pass. So if git-foo command should create a
file 'bar' but you discovered a bug that it doesn't, you can
write a test like this:
test_expect_failure 'git-foo should create bar' '
rm -f bar &&
git foo &&
test -f bar
'
This construct acts similar to test_expect_success, but instead
of reporting "ok/FAIL" like test_expect_success does, the
outcome is reported as "FIXED/still broken".
Signed-off-by: Junio C Hamano <gitster@pobox.com>
|
|
|
Signed-off-by: David Symonds <dsymonds@gmail.com>
Signed-off-by: Junio C Hamano <gitster@pobox.com>
|
