diff options
Diffstat (limited to 'include/net')
| -rw-r--r-- | include/net/atmclip.h | 1 | ||||
| -rw-r--r-- | include/net/cfg80211.h | 238 | ||||
| -rw-r--r-- | include/net/inet_ecn.h | 4 | ||||
| -rw-r--r-- | include/net/inet_hashtables.h | 4 | ||||
| -rw-r--r-- | include/net/ip.h | 1 | ||||
| -rw-r--r-- | include/net/ip_vs.h | 4 | ||||
| -rw-r--r-- | include/net/ipv6.h | 4 | ||||
| -rw-r--r-- | include/net/ipx.h | 2 | ||||
| -rw-r--r-- | include/net/mac80211.h | 234 | ||||
| -rw-r--r-- | include/net/net_namespace.h | 27 | ||||
| -rw-r--r-- | include/net/netns/ipv4.h | 13 | ||||
| -rw-r--r-- | include/net/netrom.h | 4 | ||||
| -rw-r--r-- | include/net/phonet/phonet.h | 1 | ||||
| -rw-r--r-- | include/net/phonet/pn_dev.h | 5 | ||||
| -rw-r--r-- | include/net/pkt_sched.h | 1 | ||||
| -rw-r--r-- | include/net/sch_generic.h | 7 | ||||
| -rw-r--r-- | include/net/sctp/checksum.h | 14 | ||||
| -rw-r--r-- | include/net/sctp/sctp.h | 2 | ||||
| -rw-r--r-- | include/net/sctp/structs.h | 7 | ||||
| -rw-r--r-- | include/net/sock.h | 49 | ||||
| -rw-r--r-- | include/net/transp_v6.h | 2 | ||||
| -rw-r--r-- | include/net/wireless.h | 71 |
22 files changed, 595 insertions, 100 deletions
diff --git a/include/net/atmclip.h b/include/net/atmclip.h index b5a51a7bb364..467c531b8a7e 100644 --- a/include/net/atmclip.h +++ b/include/net/atmclip.h @@ -50,7 +50,6 @@ struct atmarp_entry { struct clip_priv { int number; /* for convenience ... */ spinlock_t xoff_lock; /* ensures that pop is atomic (SMP) */ - struct net_device_stats stats; struct net_device *next; /* next CLIP interface */ }; diff --git a/include/net/cfg80211.h b/include/net/cfg80211.h index 23c0ab74ded6..c0d1f5b708c5 100644 --- a/include/net/cfg80211.h +++ b/include/net/cfg80211.h @@ -4,6 +4,10 @@ #include <linux/netlink.h> #include <linux/skbuff.h> #include <linux/nl80211.h> +#include <linux/if_ether.h> +#include <linux/ieee80211.h> +#include <linux/wireless.h> +#include <net/iw_handler.h> #include <net/genetlink.h> /* remove once we remove the wext stuff */ #include <net/iw_handler.h> @@ -112,12 +116,14 @@ struct beacon_parameters { * @STATION_FLAG_SHORT_PREAMBLE: station is capable of receiving frames * with short preambles * @STATION_FLAG_WME: station is WME/QoS capable + * @STATION_FLAG_MFP: station uses management frame protection */ enum station_flags { STATION_FLAG_CHANGED = 1<<0, STATION_FLAG_AUTHORIZED = 1<<NL80211_STA_FLAG_AUTHORIZED, STATION_FLAG_SHORT_PREAMBLE = 1<<NL80211_STA_FLAG_SHORT_PREAMBLE, STATION_FLAG_WME = 1<<NL80211_STA_FLAG_WME, + STATION_FLAG_MFP = 1<<NL80211_STA_FLAG_MFP, }; /** @@ -355,6 +361,51 @@ enum reg_set_by { REGDOM_SET_BY_COUNTRY_IE, }; +/** + * enum environment_cap - Environment parsed from country IE + * @ENVIRON_ANY: indicates country IE applies to both indoor and + * outdoor operation. + * @ENVIRON_INDOOR: indicates country IE applies only to indoor operation + * @ENVIRON_OUTDOOR: indicates country IE applies only to outdoor operation + */ +enum environment_cap { + ENVIRON_ANY, + ENVIRON_INDOOR, + ENVIRON_OUTDOOR, +}; + +/** + * struct regulatory_request - receipt of last regulatory request + * + * @wiphy: this is set if this request's initiator is + * %REGDOM_SET_BY_COUNTRY_IE or %REGDOM_SET_BY_DRIVER. This + * can be used by the wireless core to deal with conflicts + * and potentially inform users of which devices specifically + * cased the conflicts. + * @initiator: indicates who sent this request, could be any of + * of those set in reg_set_by, %REGDOM_SET_BY_* + * @alpha2: the ISO / IEC 3166 alpha2 country code of the requested + * regulatory domain. We have a few special codes: + * 00 - World regulatory domain + * 99 - built by driver but a specific alpha2 cannot be determined + * 98 - result of an intersection between two regulatory domains + * @intersect: indicates whether the wireless core should intersect + * the requested regulatory domain with the presently set regulatory + * domain. + * @country_ie_checksum: checksum of the last processed and accepted + * country IE + * @country_ie_env: lets us know if the AP is telling us we are outdoor, + * indoor, or if it doesn't matter + */ +struct regulatory_request { + struct wiphy *wiphy; + enum reg_set_by initiator; + char alpha2[2]; + bool intersect; + u32 country_ie_checksum; + enum environment_cap country_ie_env; +}; + struct ieee80211_freq_range { u32 start_freq_khz; u32 end_freq_khz; @@ -431,6 +482,26 @@ struct ieee80211_txq_params { u8 aifs; }; +/** + * struct mgmt_extra_ie_params - Extra management frame IE parameters + * + * Used to add extra IE(s) into management frames. If the driver cannot add the + * requested data into all management frames of the specified subtype that are + * generated in kernel or firmware/hardware, it must reject the configuration + * call. The IE data buffer is added to the end of the specified management + * frame body after all other IEs. This addition is not applied to frames that + * are injected through a monitor interface. + * + * @subtype: Management frame subtype + * @ies: IE data buffer or %NULL to remove previous data + * @ies_len: Length of @ies in octets + */ +struct mgmt_extra_ie_params { + u8 subtype; + u8 *ies; + int ies_len; +}; + /* from net/wireless.h */ struct wiphy; @@ -438,6 +509,85 @@ struct wiphy; struct ieee80211_channel; /** + * struct cfg80211_ssid - SSID description + * @ssid: the SSID + * @ssid_len: length of the ssid + */ +struct cfg80211_ssid { + u8 ssid[IEEE80211_MAX_SSID_LEN]; + u8 ssid_len; +}; + +/** + * struct cfg80211_scan_request - scan request description + * + * @ssids: SSIDs to scan for (active scan only) + * @n_ssids: number of SSIDs + * @channels: channels to scan on. + * @n_channels: number of channels for each band + * @wiphy: the wiphy this was for + * @ifidx: the interface index + */ +struct cfg80211_scan_request { + struct cfg80211_ssid *ssids; + int n_ssids; + struct ieee80211_channel **channels; + u32 n_channels; + + /* internal */ + struct wiphy *wiphy; + int ifidx; +}; + +/** + * enum cfg80211_signal_type - signal type + * + * @CFG80211_SIGNAL_TYPE_NONE: no signal strength information available + * @CFG80211_SIGNAL_TYPE_MBM: signal strength in mBm (100*dBm) + * @CFG80211_SIGNAL_TYPE_UNSPEC: signal strength, increasing from 0 through 100 + */ +enum cfg80211_signal_type { + CFG80211_SIGNAL_TYPE_NONE, + CFG80211_SIGNAL_TYPE_MBM, + CFG80211_SIGNAL_TYPE_UNSPEC, +}; + +/** + * struct cfg80211_bss - BSS description + * + * This structure describes a BSS (which may also be a mesh network) + * for use in scan results and similar. + * + * @bssid: BSSID of the BSS + * @tsf: timestamp of last received update + * @beacon_interval: the beacon interval as from the frame + * @capability: the capability field in host byte order + * @information_elements: the information elements (Note that there + * is no guarantee that these are well-formed!) + * @len_information_elements: total length of the information elements + * @signal: signal strength value + * @signal_type: signal type + * @free_priv: function pointer to free private data + * @priv: private area for driver use, has at least wiphy->bss_priv_size bytes + */ +struct cfg80211_bss { + struct ieee80211_channel *channel; + + u8 bssid[ETH_ALEN]; + u64 tsf; + u16 beacon_interval; + u16 capability; + u8 *information_elements; + size_t len_information_elements; + + s32 signal; + enum cfg80211_signal_type signal_type; + + void (*free_priv)(struct cfg80211_bss *bss); + u8 priv[0] __attribute__((__aligned__(sizeof(void *)))); +}; + +/** * struct cfg80211_ops - backend description for wireless configuration * * This struct is registered by fullmac card drivers and/or wireless stacks @@ -450,6 +600,9 @@ struct ieee80211_channel; * wireless extensions but this is subject to reevaluation as soon as this * code is used more widely and we have a first user without wext. * + * @suspend: wiphy device needs to be suspended + * @resume: wiphy device needs to be resumed + * * @add_virtual_intf: create a new virtual interface with the given name, * must set the struct wireless_dev's iftype. * @@ -471,6 +624,8 @@ struct ieee80211_channel; * * @set_default_key: set the default key on an interface * + * @set_default_mgmt_key: set the default management frame key on an interface + * * @add_beacon: Add a beacon with given parameters, @head, @interval * and @dtim_period will be valid, @tail is optional. * @set_beacon: Change the beacon parameters for an access point mode @@ -497,8 +652,18 @@ struct ieee80211_channel; * @set_txq_params: Set TX queue parameters * * @set_channel: Set channel + * + * @set_mgmt_extra_ie: Set extra IE data for management frames + * + * @scan: Request to do a scan. If returning zero, the scan request is given + * the driver, and will be valid until passed to cfg80211_scan_done(). + * For scan results, call cfg80211_inform_bss(); you can call this outside + * the scan/scan_done bracket too. */ struct cfg80211_ops { + int (*suspend)(struct wiphy *wiphy); + int (*resume)(struct wiphy *wiphy); + int (*add_virtual_intf)(struct wiphy *wiphy, char *name, enum nl80211_iftype type, u32 *flags, struct vif_params *params); @@ -518,6 +683,9 @@ struct cfg80211_ops { int (*set_default_key)(struct wiphy *wiphy, struct net_device *netdev, u8 key_index); + int (*set_default_mgmt_key)(struct wiphy *wiphy, + struct net_device *netdev, + u8 key_index); int (*add_beacon)(struct wiphy *wiphy, struct net_device *dev, struct beacon_parameters *info); @@ -564,6 +732,13 @@ struct cfg80211_ops { int (*set_channel)(struct wiphy *wiphy, struct ieee80211_channel *chan, enum nl80211_channel_type channel_type); + + int (*set_mgmt_extra_ie)(struct wiphy *wiphy, + struct net_device *dev, + struct mgmt_extra_ie_params *params); + + int (*scan)(struct wiphy *wiphy, struct net_device *dev, + struct cfg80211_scan_request *request); }; /* temporary wext handlers */ @@ -574,5 +749,68 @@ int cfg80211_wext_siwmode(struct net_device *dev, struct iw_request_info *info, u32 *mode, char *extra); int cfg80211_wext_giwmode(struct net_device *dev, struct iw_request_info *info, u32 *mode, char *extra); +int cfg80211_wext_siwscan(struct net_device *dev, + struct iw_request_info *info, + union iwreq_data *wrqu, char *extra); +int cfg80211_wext_giwscan(struct net_device *dev, + struct iw_request_info *info, + struct iw_point *data, char *extra); + +/** + * cfg80211_scan_done - notify that scan finished + * + * @request: the corresponding scan request + * @aborted: set to true if the scan was aborted for any reason, + * userspace will be notified of that + */ +void cfg80211_scan_done(struct cfg80211_scan_request *request, bool aborted); + +/** + * cfg80211_inform_bss - inform cfg80211 of a new BSS + * + * @wiphy: the wiphy reporting the BSS + * @bss: the found BSS + * @gfp: context flags + * + * This informs cfg80211 that BSS information was found and + * the BSS should be updated/added. + */ +struct cfg80211_bss* +cfg80211_inform_bss_frame(struct wiphy *wiphy, + struct ieee80211_channel *channel, + struct ieee80211_mgmt *mgmt, size_t len, + s32 signal, enum cfg80211_signal_type sigtype, + gfp_t gfp); + +struct cfg80211_bss *cfg80211_get_bss(struct wiphy *wiphy, + struct ieee80211_channel *channel, + const u8 *bssid, + const u8 *ssid, size_t ssid_len, + u16 capa_mask, u16 capa_val); +static inline struct cfg80211_bss * +cfg80211_get_ibss(struct wiphy *wiphy, + struct ieee80211_channel *channel, + const u8 *ssid, size_t ssid_len) +{ + return cfg80211_get_bss(wiphy, channel, NULL, ssid, ssid_len, + WLAN_CAPABILITY_IBSS, WLAN_CAPABILITY_IBSS); +} + +struct cfg80211_bss *cfg80211_get_mesh(struct wiphy *wiphy, + struct ieee80211_channel *channel, + const u8 *meshid, size_t meshidlen, + const u8 *meshcfg); +void cfg80211_put_bss(struct cfg80211_bss *bss); +/** + * cfg80211_unlink_bss - unlink BSS from internal data structures + * @wiphy: the wiphy + * @bss: the bss to remove + * + * This function removes the given BSS from the internal data structures + * thereby making it no longer show up in scan results etc. Use this + * function when you detect a BSS is gone. Normally BSSes will also time + * out, so it is not necessary to use this function at all. + */ +void cfg80211_unlink_bss(struct wiphy *wiphy, struct cfg80211_bss *bss); #endif /* __NET_CFG80211_H */ diff --git a/include/net/inet_ecn.h b/include/net/inet_ecn.h index 7040a782c656..9b5d08f4f6e8 100644 --- a/include/net/inet_ecn.h +++ b/include/net/inet_ecn.h @@ -113,12 +113,12 @@ static inline void ipv6_copy_dscp(unsigned int dscp, struct ipv6hdr *inner) static inline int INET_ECN_set_ce(struct sk_buff *skb) { switch (skb->protocol) { - case __constant_htons(ETH_P_IP): + case cpu_to_be16(ETH_P_IP): if (skb->network_header + sizeof(struct iphdr) <= skb->tail) return IP_ECN_set_ce(ip_hdr(skb)); break; - case __constant_htons(ETH_P_IPV6): + case cpu_to_be16(ETH_P_IPV6): if (skb->network_header + sizeof(struct ipv6hdr) <= skb->tail) return IP6_ECN_set_ce(ipv6_hdr(skb)); break; diff --git a/include/net/inet_hashtables.h b/include/net/inet_hashtables.h index d0a043153cc6..a44e2248b2ef 100644 --- a/include/net/inet_hashtables.h +++ b/include/net/inet_hashtables.h @@ -82,6 +82,7 @@ struct inet_bind_bucket { #endif unsigned short port; signed short fastreuse; + int num_owners; struct hlist_node node; struct hlist_head owners; }; @@ -133,7 +134,7 @@ struct inet_hashinfo { struct inet_bind_hashbucket *bhash; unsigned int bhash_size; - /* Note : 4 bytes padding on 64 bit arches */ + /* 4 bytes hole on 64 bit */ struct kmem_cache *bind_bucket_cachep; @@ -150,6 +151,7 @@ struct inet_hashinfo { struct inet_listen_hashbucket listening_hash[INET_LHTABLE_SIZE] ____cacheline_aligned_in_smp; + atomic_t bsockets; }; static inline struct inet_ehash_bucket *inet_ehash_bucket( diff --git a/include/net/ip.h b/include/net/ip.h index 10868139e656..4ac7577f98d0 100644 --- a/include/net/ip.h +++ b/include/net/ip.h @@ -55,6 +55,7 @@ struct ipcm_cookie __be32 addr; int oif; struct ip_options *opt; + union skb_shared_tx shtx; }; #define IPCB(skb) ((struct inet_skb_parm*)((skb)->cb)) diff --git a/include/net/ip_vs.h b/include/net/ip_vs.h index ab9b003ab671..bbae1e87efcd 100644 --- a/include/net/ip_vs.h +++ b/include/net/ip_vs.h @@ -184,8 +184,8 @@ static inline const char *ip_vs_dbg_addr(int af, char *buf, size_t buf_len, /* * The port number of FTP service (in network order). */ -#define FTPPORT __constant_htons(21) -#define FTPDATA __constant_htons(20) +#define FTPPORT cpu_to_be16(21) +#define FTPDATA cpu_to_be16(20) /* * TCP State Values diff --git a/include/net/ipv6.h b/include/net/ipv6.h index 6d5b58a1c743..c1f16fc49ade 100644 --- a/include/net/ipv6.h +++ b/include/net/ipv6.h @@ -196,8 +196,8 @@ struct ip6_flowlabel struct net *fl_net; }; -#define IPV6_FLOWINFO_MASK __constant_htonl(0x0FFFFFFF) -#define IPV6_FLOWLABEL_MASK __constant_htonl(0x000FFFFF) +#define IPV6_FLOWINFO_MASK cpu_to_be32(0x0FFFFFFF) +#define IPV6_FLOWLABEL_MASK cpu_to_be32(0x000FFFFF) struct ipv6_fl_socklist { diff --git a/include/net/ipx.h b/include/net/ipx.h index 4cc0b4eca948..a14121dd1932 100644 --- a/include/net/ipx.h +++ b/include/net/ipx.h @@ -27,7 +27,7 @@ struct ipx_address { struct ipxhdr { __be16 ipx_checksum __attribute__ ((packed)); -#define IPX_NO_CHECKSUM __constant_htons(0xFFFF) +#define IPX_NO_CHECKSUM cpu_to_be16(0xFFFF) __be16 ipx_pktsize __attribute__ ((packed)); __u8 ipx_tctrl; __u8 ipx_type; diff --git a/include/net/mac80211.h b/include/net/mac80211.h index 559422fc0943..88fa3e03e3e9 100644 --- a/include/net/mac80211.h +++ b/include/net/mac80211.h @@ -207,7 +207,7 @@ struct ieee80211_bss_conf { u16 beacon_int; u16 assoc_capability; u64 timestamp; - u64 basic_rates; + u32 basic_rates; struct ieee80211_bss_ht_conf ht; }; @@ -262,6 +262,26 @@ enum mac80211_tx_control_flags { IEEE80211_TX_CTL_RATE_CTRL_PROBE = BIT(12), }; +/** + * enum mac80211_rate_control_flags - per-rate flags set by the + * Rate Control algorithm. + * + * These flags are set by the Rate control algorithm for each rate during tx, + * in the @flags member of struct ieee80211_tx_rate. + * + * @IEEE80211_TX_RC_USE_RTS_CTS: Use RTS/CTS exchange for this rate. + * @IEEE80211_TX_RC_USE_CTS_PROTECT: CTS-to-self protection is required. + * This is set if the current BSS requires ERP protection. + * @IEEE80211_TX_RC_USE_SHORT_PREAMBLE: Use short preamble. + * @IEEE80211_TX_RC_MCS: HT rate. + * @IEEE80211_TX_RC_GREEN_FIELD: Indicates whether this rate should be used in + * Greenfield mode. + * @IEEE80211_TX_RC_40_MHZ_WIDTH: Indicates if the Channel Width should be 40 MHz. + * @IEEE80211_TX_RC_DUP_DATA: The frame should be transmitted on both of the + * adjacent 20 MHz channels, if the current channel type is + * NL80211_CHAN_HT40MINUS or NL80211_CHAN_HT40PLUS. + * @IEEE80211_TX_RC_SHORT_GI: Short Guard interval should be used for this rate. + */ enum mac80211_rate_control_flags { IEEE80211_TX_RC_USE_RTS_CTS = BIT(0), IEEE80211_TX_RC_USE_CTS_PROTECT = BIT(1), @@ -507,11 +527,6 @@ static inline int __deprecated __IEEE80211_CONF_SHORT_SLOT_TIME(void) } #define IEEE80211_CONF_SHORT_SLOT_TIME (__IEEE80211_CONF_SHORT_SLOT_TIME()) -struct ieee80211_ht_conf { - bool enabled; - enum nl80211_channel_type channel_type; -}; - /** * enum ieee80211_conf_changed - denotes which configuration changed * @@ -520,10 +535,10 @@ struct ieee80211_ht_conf { * @IEEE80211_CONF_CHANGE_LISTEN_INTERVAL: the listen interval changed * @IEEE80211_CONF_CHANGE_RADIOTAP: the radiotap flag changed * @IEEE80211_CONF_CHANGE_PS: the PS flag changed + * @IEEE80211_CONF_CHANGE_DYNPS_TIMEOUT: the dynamic PS timeout changed * @IEEE80211_CONF_CHANGE_POWER: the TX power changed - * @IEEE80211_CONF_CHANGE_CHANNEL: the channel changed + * @IEEE80211_CONF_CHANGE_CHANNEL: the channel/channel_type changed * @IEEE80211_CONF_CHANGE_RETRY_LIMITS: retry limits changed - * @IEEE80211_CONF_CHANGE_HT: HT configuration changed */ enum ieee80211_conf_changed { IEEE80211_CONF_CHANGE_RADIO_ENABLED = BIT(0), @@ -531,10 +546,10 @@ enum ieee80211_conf_changed { IEEE80211_CONF_CHANGE_LISTEN_INTERVAL = BIT(2), IEEE80211_CONF_CHANGE_RADIOTAP = BIT(3), IEEE80211_CONF_CHANGE_PS = BIT(4), - IEEE80211_CONF_CHANGE_POWER = BIT(5), - IEEE80211_CONF_CHANGE_CHANNEL = BIT(6), - IEEE80211_CONF_CHANGE_RETRY_LIMITS = BIT(7), - IEEE80211_CONF_CHANGE_HT = BIT(8), + IEEE80211_CONF_CHANGE_DYNPS_TIMEOUT = BIT(5), + IEEE80211_CONF_CHANGE_POWER = BIT(6), + IEEE80211_CONF_CHANGE_CHANNEL = BIT(7), + IEEE80211_CONF_CHANGE_RETRY_LIMITS = BIT(8), }; /** @@ -547,8 +562,9 @@ enum ieee80211_conf_changed { * @listen_interval: listen interval in units of beacon interval * @flags: configuration flags defined above * @power_level: requested transmit power (in dBm) + * @dynamic_ps_timeout: dynamic powersave timeout (in ms) * @channel: the channel to tune to - * @ht: the HT configuration for the device + * @channel_type: the channel (HT) type * @long_frame_max_tx_count: Maximum number of transmissions for a "long" frame * (a frame not RTS protected), called "dot11LongRetryLimit" in 802.11, * but actually means the number of transmissions not the number of retries @@ -559,7 +575,7 @@ enum ieee80211_conf_changed { struct ieee80211_conf { int beacon_int; u32 flags; - int power_level; + int power_level, dynamic_ps_timeout; u16 listen_interval; bool radio_enabled; @@ -567,7 +583,7 @@ struct ieee80211_conf { u8 long_frame_max_tx_count, short_frame_max_tx_count; struct ieee80211_channel *channel; - struct ieee80211_ht_conf ht; + enum nl80211_channel_type channel_type; }; /** @@ -630,10 +646,12 @@ struct ieee80211_if_init_conf { * @IEEE80211_IFCC_BSSID: The BSSID changed. * @IEEE80211_IFCC_BEACON: The beacon for this interface changed * (currently AP and MESH only), use ieee80211_beacon_get(). + * @IEEE80211_IFCC_BEACON_ENABLED: The enable_beacon value changed. */ enum ieee80211_if_conf_change { - IEEE80211_IFCC_BSSID = BIT(0), - IEEE80211_IFCC_BEACON = BIT(1), + IEEE80211_IFCC_BSSID = BIT(0), + IEEE80211_IFCC_BEACON = BIT(1), + IEEE80211_IFCC_BEACON_ENABLED = BIT(2), }; /** @@ -641,13 +659,16 @@ enum ieee80211_if_conf_change { * * @changed: parameters that have changed, see &enum ieee80211_if_conf_change. * @bssid: BSSID of the network we are associated to/creating. + * @enable_beacon: Indicates whether beacons can be sent. + * This is valid only for AP/IBSS/MESH modes. * * This structure is passed to the config_interface() callback of * &struct ieee80211_hw. */ struct ieee80211_if_conf { u32 changed; - u8 *bssid; + const u8 *bssid; + bool enable_beacon; }; /** @@ -655,11 +676,13 @@ struct ieee80211_if_conf { * @ALG_WEP: WEP40 or WEP104 * @ALG_TKIP: TKIP * @ALG_CCMP: CCMP (AES) + * @ALG_AES_CMAC: AES-128-CMAC */ enum ieee80211_key_alg { ALG_WEP, ALG_TKIP, ALG_CCMP, + ALG_AES_CMAC, }; /** @@ -688,12 +711,16 @@ enum ieee80211_key_len { * generation in software. * @IEEE80211_KEY_FLAG_PAIRWISE: Set by mac80211, this flag indicates * that the key is pairwise rather then a shared key. + * @IEEE80211_KEY_FLAG_SW_MGMT: This flag should be set by the driver for a + * CCMP key if it requires CCMP encryption of management frames (MFP) to + * be done in software. */ enum ieee80211_key_flags { IEEE80211_KEY_FLAG_WMM_STA = 1<<0, IEEE80211_KEY_FLAG_GENERATE_IV = 1<<1, IEEE80211_KEY_FLAG_GENERATE_MMIC= 1<<2, IEEE80211_KEY_FLAG_PAIRWISE = 1<<3, + IEEE80211_KEY_FLAG_SW_MGMT = 1<<4, }; /** @@ -714,8 +741,8 @@ enum ieee80211_key_flags { * - Temporal Encryption Key (128 bits) * - Temporal Authenticator Tx MIC Key (64 bits) * - Temporal Authenticator Rx MIC Key (64 bits) - * @icv_len: FIXME - * @iv_len: FIXME + * @icv_len: The ICV length for this key type + * @iv_len: The IV length for this key type */ struct ieee80211_key_conf { enum ieee80211_key_alg alg; @@ -759,7 +786,7 @@ enum set_key_cmd { * sizeof(void *), size is determined in hw information. */ struct ieee80211_sta { - u64 supp_rates[IEEE80211_NUM_BANDS]; + u32 supp_rates[IEEE80211_NUM_BANDS]; u8 addr[ETH_ALEN]; u16 aid; struct ieee80211_sta_ht_cap ht_cap; @@ -833,11 +860,6 @@ enum ieee80211_tkip_key_type { * expect values between 0 and @max_signal. * If possible please provide dB or dBm instead. * - * @IEEE80211_HW_SIGNAL_DB: - * Hardware gives signal values in dB, decibel difference from an - * arbitrary, fixed reference. We expect values between 0 and @max_signal. - * If possible please provide dBm instead. - * * @IEEE80211_HW_SIGNAL_DBM: * Hardware gives signal values in dBm, decibel difference from * one milliwatt. This is the preferred method since it is standardized @@ -854,10 +876,18 @@ enum ieee80211_tkip_key_type { * @IEEE80211_HW_AMPDU_AGGREGATION: * Hardware supports 11n A-MPDU aggregation. * - * @IEEE80211_HW_NO_STACK_DYNAMIC_PS: - * Hardware which has dynamic power save support, meaning - * that power save is enabled in idle periods, and don't need support - * from stack. + * @IEEE80211_HW_SUPPORTS_PS: + * Hardware has power save support (i.e. can go to sleep). + * + * @IEEE80211_HW_PS_NULLFUNC_STACK: + * Hardware requires nullfunc frame handling in stack, implies + * stack support for dynamic PS. + * + * @IEEE80211_HW_SUPPORTS_DYNAMIC_PS: + * Hardware has support for dynamic PS. + * + * @IEEE80211_HW_MFP_CAPABLE: + * Hardware supports management frame protection (MFP, IEEE 802.11w). */ enum ieee80211_hw_flags { IEEE80211_HW_RX_INCLUDES_FCS = 1<<1, @@ -865,12 +895,14 @@ enum ieee80211_hw_flags { IEEE80211_HW_2GHZ_SHORT_SLOT_INCAPABLE = 1<<3, IEEE80211_HW_2GHZ_SHORT_PREAMBLE_INCAPABLE = 1<<4, IEEE80211_HW_SIGNAL_UNSPEC = 1<<5, - IEEE80211_HW_SIGNAL_DB = 1<<6, - IEEE80211_HW_SIGNAL_DBM = 1<<7, - IEEE80211_HW_NOISE_DBM = 1<<8, - IEEE80211_HW_SPECTRUM_MGMT = 1<<9, - IEEE80211_HW_AMPDU_AGGREGATION = 1<<10, - IEEE80211_HW_NO_STACK_DYNAMIC_PS = 1<<11, + IEEE80211_HW_SIGNAL_DBM = 1<<6, + IEEE80211_HW_NOISE_DBM = 1<<7, + IEEE80211_HW_SPECTRUM_MGMT = 1<<8, + IEEE80211_HW_AMPDU_AGGREGATION = 1<<9, + IEEE80211_HW_SUPPORTS_PS = 1<<10, + IEEE80211_HW_PS_NULLFUNC_STACK = 1<<11, + IEEE80211_HW_SUPPORTS_DYNAMIC_PS = 1<<12, + IEEE80211_HW_MFP_CAPABLE = 1<<13, }; /** @@ -890,9 +922,8 @@ enum ieee80211_hw_flags { * @workqueue: single threaded workqueue available for driver use, * allocated by mac80211 on registration and flushed when an * interface is removed. - * NOTICE: All work performed on this workqueue should NEVER - * acquire the RTNL lock (i.e. Don't use the function - * ieee80211_iterate_active_interfaces()) + * NOTICE: All work performed on this workqueue must not + * acquire the RTNL lock. * * @priv: pointer to private area that was allocated for driver use * along with this structure. @@ -952,6 +983,19 @@ struct ieee80211_hw { }; /** + * wiphy_to_ieee80211_hw - return a mac80211 driver hw struct from a wiphy + * + * @wiphy: the &struct wiphy which we want to query + * + * mac80211 drivers can use this to get to their respective + * &struct ieee80211_hw. Drivers wishing to get to their own private + * structure can then access it via hw->priv. Note that mac802111 drivers should + * not use wiphy_priv() to try to get their private driver structure as this + * is already used internally by mac80211. + */ +struct ieee80211_hw *wiphy_to_ieee80211_hw(struct wiphy *wiphy); + +/** * SET_IEEE80211_DEV - set device for 802.11 hardware * * @hw: the &struct ieee80211_hw to set the device for @@ -1018,16 +1062,12 @@ ieee80211_get_alt_retry_rate(const struct ieee80211_hw *hw, * * The set_key() callback in the &struct ieee80211_ops for a given * device is called to enable hardware acceleration of encryption and - * decryption. The callback takes an @address parameter that will be - * the broadcast address for default keys, the other station's hardware - * address for individual keys or the zero address for keys that will - * be used only for transmission. + * decryption. The callback takes a @sta parameter that will be NULL + * for default keys or keys used for transmission only, or point to + * the station information for the peer for individual keys. * Multiple transmission keys with the same key index may be used when * VLANs are configured for an access point. * - * The @local_address parameter will always be set to our own address, - * this is only relevant if you support multiple local addresses. - * * When transmitting, the TX control data will use the @hw_key_idx * selected by the driver by modifying the &struct ieee80211_key_conf * pointed to by the @key parameter to the set_key() function. @@ -1061,6 +1101,42 @@ ieee80211_get_alt_retry_rate(const struct ieee80211_hw *hw, */ /** + * DOC: Powersave support + * + * mac80211 has support for various powersave implementations. + * + * First, it can support hardware that handles all powersaving by + * itself, such hardware should simply set the %IEEE80211_HW_SUPPORTS_PS + * hardware flag. In that case, it will be told about the desired + * powersave mode depending on the association status, and the driver + * must take care of sending nullfunc frames when necessary, i.e. when + * entering and leaving powersave mode. The driver is required to look at + * the AID in beacons and signal to the AP that it woke up when it finds + * traffic directed to it. This mode supports dynamic PS by simply + * enabling/disabling PS. + * + * Additionally, such hardware may set the %IEEE80211_HW_SUPPORTS_DYNAMIC_PS + * flag to indicate that it can support dynamic PS mode itself (see below). + * + * Other hardware designs cannot send nullfunc frames by themselves and also + * need software support for parsing the TIM bitmap. This is also supported + * by mac80211 by combining the %IEEE80211_HW_SUPPORTS_PS and + * %IEEE80211_HW_PS_NULLFUNC_STACK flags. The hardware is of course still + * required to pass up beacons. Additionally, in this case, mac80211 will + * wake up the hardware when multicast traffic is announced in the beacon. + * + * FIXME: I don't think we can be fast enough in software when we want to + * receive multicast traffic? + * + * Dynamic powersave mode is an extension to normal powersave mode in which + * the hardware stays awake for a user-specified period of time after sending + * a frame so that reply frames need not be buffered and therefore delayed + * to the next wakeup. This can either be supported by hardware, in which case + * the driver needs to look at the @dynamic_ps_timeout hardware configuration + * value, or by the stack if all nullfunc handling is in the stack. + */ + +/** * DOC: Frame filtering * * mac80211 requires to see many management frames for proper @@ -1172,6 +1248,8 @@ enum ieee80211_ampdu_mlme_action { * configuration in the TX control data. This handler should, * preferably, never fail and stop queues appropriately, more * importantly, however, it must never fail for A-MPDU-queues. + * This function should return NETDEV_TX_OK except in very + * limited cases. * Must be implemented and atomic. * * @start: Called before the first netdevice attached to the hardware @@ -1212,9 +1290,12 @@ enum ieee80211_ampdu_mlme_action { * * @config: Handler for configuration requests. IEEE 802.11 code calls this * function to change hardware configuration, e.g., channel. + * This function should never fail but returns a negative error code + * if it does. * * @config_interface: Handler for configuration requests related to interfaces * (e.g. BSSID changes.) + * Returns a negative error code which will be seen in userspace. * * @bss_info_changed: Handler for configuration requests related to BSS * parameters that may vary during BSS's lifespan, and may affect low @@ -1232,8 +1313,9 @@ enum ieee80211_ampdu_mlme_action { * * @set_key: See the section "Hardware crypto acceleration" * This callback can sleep, and is only called between add_interface - * and remove_interface calls, i.e. while the interface with the - * given local_address is enabled. + * and remove_interface calls, i.e. while the given virtual interface + * is enabled. + * Returns a negative error code if the key can't be added. * * @update_tkip_key: See the section "Hardware crypto acceleration" * This callback will be called in the context of Rx. Called for drivers @@ -1245,8 +1327,10 @@ enum ieee80211_ampdu_mlme_action { * bands. When the scan finishes, ieee80211_scan_completed() must be * called; note that it also must be called when the scan cannot finish * because the hardware is turned off! Anything else is a bug! + * Returns a negative error code which will be seen in userspace. * - * @get_stats: return low-level statistics + * @get_stats: Return low-level statistics. + * Returns zero if statistics are available. * * @get_tkip_seq: If your device implements TKIP encryption in hardware this * callback should be provided to read the TKIP transmit IVs (both IV32 @@ -1260,6 +1344,7 @@ enum ieee80211_ampdu_mlme_action { * * @conf_tx: Configure TX queue parameters (EDCF (aifs, cw_min, cw_max), * bursting) for a hardware TX queue. + * Returns a negative error code on failure. * * @get_tx_stats: Get statistics of the current TX queue status. This is used * to get number of currently queued packets (queue length), maximum queue @@ -1268,8 +1353,12 @@ enum ieee80211_ampdu_mlme_action { * hw->ampdu_queues items. * * @get_tsf: Get the current TSF timer value from firmware/hardware. Currently, - * this is only used for IBSS mode debugging and, as such, is not a - * required function. Must be atomic. + * this is only used for IBSS mode BSSID merging and debugging. Is not a + * required function. + * + * @set_tsf: Set the TSF timer to the specified value in the firmware/hardware. + * Currently, this is only used for IBSS mode debugging. Is not a + * required function. * * @reset_tsf: Reset the TSF timer and allow firmware/hardware to synchronize * with other STAs in the IBSS. This is only used in IBSS mode. This @@ -1279,13 +1368,15 @@ enum ieee80211_ampdu_mlme_action { * @tx_last_beacon: Determine whether the last IBSS beacon was sent by us. * This is needed only for IBSS mode and the result of this function is * used to determine whether to reply to Probe Requests. + * Returns non-zero if this device sent the last beacon. * * @ampdu_action: Perform a certain A-MPDU action * The RA/TID combination determines the destination and TID we want * the ampdu action to be performed for. The action is defined through * ieee80211_ampdu_mlme_action. Starting sequence number (@ssn) - * is the first frame we expect to perform the action on. notice + * is the first frame we expect to perform the action on. Notice * that TX/RX_STOP can pass NULL for this parameter. + * Returns a negative error code on failure. */ struct ieee80211_ops { int (*tx)(struct ieee80211_hw *hw, struct sk_buff *skb); @@ -1310,12 +1401,13 @@ struct ieee80211_ops { int (*set_tim)(struct ieee80211_hw *hw, struct ieee80211_sta *sta, bool set); int (*set_key)(struct ieee80211_hw *hw, enum set_key_cmd cmd, - const u8 *local_address, const u8 *address, + struct ieee80211_vif *vif, struct ieee80211_sta *sta, struct ieee80211_key_conf *key); void (*update_tkip_key)(struct ieee80211_hw *hw, struct ieee80211_key_conf *conf, const u8 *address, u32 iv32, u16 *phase1key); - int (*hw_scan)(struct ieee80211_hw *hw, u8 *ssid, size_t len); + int (*hw_scan)(struct ieee80211_hw *hw, + struct cfg80211_scan_request *req); int (*get_stats)(struct ieee80211_hw *hw, struct ieee80211_low_level_stats *stats); void (*get_tkip_seq)(struct ieee80211_hw *hw, u8 hw_key_idx, @@ -1328,6 +1420,7 @@ struct ieee80211_ops { int (*get_tx_stats)(struct ieee80211_hw *hw, struct ieee80211_tx_queue_stats *stats); u64 (*get_tsf)(struct ieee80211_hw *hw); + void (*set_tsf)(struct ieee80211_hw *hw, u64 tsf); void (*reset_tsf)(struct ieee80211_hw *hw); int (*tx_last_beacon)(struct ieee80211_hw *hw); int (*ampdu_action)(struct ieee80211_hw *hw, @@ -1752,8 +1845,9 @@ void ieee80211_wake_queues(struct ieee80211_hw *hw); * mac80211 that the scan finished. * * @hw: the hardware that finished the scan + * @aborted: set to true if scan was aborted */ -void ieee80211_scan_completed(struct ieee80211_hw *hw); +void ieee80211_scan_completed(struct ieee80211_hw *hw, bool aborted); /** * ieee80211_iterate_active_interfaces - iterate active interfaces @@ -1962,4 +2056,34 @@ rate_lowest_index(struct ieee80211_supported_band *sband, int ieee80211_rate_control_register(struct rate_control_ops *ops); void ieee80211_rate_control_unregister(struct rate_control_ops *ops); +static inline bool +conf_is_ht20(struct ieee80211_conf *conf) +{ + return conf->channel_type == NL80211_CHAN_HT20; +} + +static inline bool +conf_is_ht40_minus(struct ieee80211_conf *conf) +{ + return conf->channel_type == NL80211_CHAN_HT40MINUS; +} + +static inline bool +conf_is_ht40_plus(struct ieee80211_conf *conf) +{ + return conf->channel_type == NL80211_CHAN_HT40PLUS; +} + +static inline bool +conf_is_ht40(struct ieee80211_conf *conf) +{ + return conf_is_ht40_minus(conf) || conf_is_ht40_plus(conf); +} + +static inline bool +conf_is_ht(struct ieee80211_conf *conf) +{ + return conf->channel_type != NL80211_CHAN_NO_HT; +} + #endif /* MAC80211_H */ diff --git a/include/net/net_namespace.h b/include/net/net_namespace.h index 6fc13d905c5f..ded434b032a4 100644 --- a/include/net/net_namespace.h +++ b/include/net/net_namespace.h @@ -109,11 +109,6 @@ extern struct list_head net_namespace_list; #ifdef CONFIG_NET_NS extern void __put_net(struct net *net); -static inline int net_alive(struct net *net) -{ - return net && atomic_read(&net->count); -} - static inline struct net *get_net(struct net *net) { atomic_inc(&net->count); @@ -145,11 +140,6 @@ int net_eq(const struct net *net1, const struct net *net2) } #else -static inline int net_alive(struct net *net) -{ - return 1; -} - static inline struct net *get_net(struct net *net) { return net; @@ -234,6 +224,23 @@ struct pernet_operations { void (*exit)(struct net *net); }; +/* + * Use these carefully. If you implement a network device and it + * needs per network namespace operations use device pernet operations, + * otherwise use pernet subsys operations. + * + * This is critically important. Most of the network code cleanup + * runs with the assumption that dev_remove_pack has been called so no + * new packets will arrive during and after the cleanup functions have + * been called. dev_remove_pack is not per namespace so instead the + * guarantee of no more packets arriving in a network namespace is + * provided by ensuring that all network devices and all sockets have + * left the network namespace before the cleanup methods are called. + * + * For the longest time the ipv4 icmp code was registered as a pernet + * device which caused kernel oops, and panics during network + * namespace cleanup. So please don't get this wrong. + */ extern int register_pernet_subsys(struct pernet_operations *); extern void unregister_pernet_subsys(struct pernet_operations *); extern int register_pernet_gen_subsys(int *id, struct pernet_operations *); diff --git a/include/net/netns/ipv4.h b/include/net/netns/ipv4.h index 977f482d97a9..2eb3814d6258 100644 --- a/include/net/netns/ipv4.h +++ b/include/net/netns/ipv4.h @@ -54,5 +54,18 @@ struct netns_ipv4 { struct timer_list rt_secret_timer; atomic_t rt_genid; + +#ifdef CONFIG_IP_MROUTE + struct sock *mroute_sk; + struct mfc_cache **mfc_cache_array; + struct vif_device *vif_table; + int maxvif; + atomic_t cache_resolve_queue_len; + int mroute_do_assert; + int mroute_do_pim; +#if defined(CONFIG_IP_PIMSM_V1) || defined(CONFIG_IP_PIMSM_V2) + int mroute_reg_vif_num; +#endif +#endif }; #endif diff --git a/include/net/netrom.h b/include/net/netrom.h index f06852bba62a..15696b1fd30f 100644 --- a/include/net/netrom.h +++ b/include/net/netrom.h @@ -59,10 +59,6 @@ enum { #define NR_MAX_WINDOW_SIZE 127 /* Maximum Window Allowable - 127 */ #define NR_MAX_PACKET_SIZE 236 /* Maximum Packet Length - 236 */ -struct nr_private { - struct net_device_stats stats; -}; - struct nr_sock { struct sock sock; ax25_address user_addr, source_addr, dest_addr; diff --git a/include/net/phonet/phonet.h b/include/net/phonet/phonet.h index 057b0a8a2885..d43f71b5ec00 100644 --- a/include/net/phonet/phonet.h +++ b/include/net/phonet/phonet.h @@ -105,7 +105,6 @@ void phonet_proto_unregister(int protocol, struct phonet_protocol *pp); int phonet_sysctl_init(void); void phonet_sysctl_exit(void); -void phonet_netlink_register(void); int isi_register(void); void isi_unregister(void); diff --git a/include/net/phonet/pn_dev.h b/include/net/phonet/pn_dev.h index aa1c59a1d33f..5054dc5ea2c2 100644 --- a/include/net/phonet/pn_dev.h +++ b/include/net/phonet/pn_dev.h @@ -28,7 +28,7 @@ struct phonet_device_list { spinlock_t lock; }; -extern struct phonet_device_list pndevs; +struct phonet_device_list *phonet_device_list(struct net *net); struct phonet_device { struct list_head list; @@ -36,8 +36,9 @@ struct phonet_device { DECLARE_BITMAP(addrs, 64); }; -void phonet_device_init(void); +int phonet_device_init(void); void phonet_device_exit(void); +int phonet_netlink_register(void); struct net_device *phonet_device_get(struct net *net); int phonet_address_add(struct net_device *dev, u8 addr); diff --git a/include/net/pkt_sched.h b/include/net/pkt_sched.h index 4082f39f5079..e37fe3129c17 100644 --- a/include/net/pkt_sched.h +++ b/include/net/pkt_sched.h @@ -85,6 +85,7 @@ extern struct qdisc_rate_table *qdisc_get_rtab(struct tc_ratespec *r, struct nlattr *tab); extern void qdisc_put_rtab(struct qdisc_rate_table *tab); extern void qdisc_put_stab(struct qdisc_size_table *tab); +extern void qdisc_warn_nonwc(char *txt, struct Qdisc *qdisc); extern void __qdisc_run(struct Qdisc *q); diff --git a/include/net/sch_generic.h b/include/net/sch_generic.h index f8c47429044a..3d78a4d22460 100644 --- a/include/net/sch_generic.h +++ b/include/net/sch_generic.h @@ -42,9 +42,10 @@ struct Qdisc int (*enqueue)(struct sk_buff *skb, struct Qdisc *dev); struct sk_buff * (*dequeue)(struct Qdisc *dev); unsigned flags; -#define TCQ_F_BUILTIN 1 -#define TCQ_F_THROTTLED 2 -#define TCQ_F_INGRESS 4 +#define TCQ_F_BUILTIN 1 +#define TCQ_F_THROTTLED 2 +#define TCQ_F_INGRESS 4 +#define TCQ_F_WARN_NONWC (1 << 16) int padded; struct Qdisc_ops *ops; struct qdisc_size_table *stab; diff --git a/include/net/sctp/checksum.h b/include/net/sctp/checksum.h index 2fec3c366e81..befc8d2a1b9f 100644 --- a/include/net/sctp/checksum.h +++ b/include/net/sctp/checksum.h @@ -46,14 +46,14 @@ #include <net/sctp/sctp.h> #include <linux/crc32c.h> -static inline __be32 sctp_crc32c(__be32 crc, u8 *buffer, u16 length) +static inline __u32 sctp_crc32c(__u32 crc, u8 *buffer, u16 length) { - return (__force __be32)crc32c((__force u32)crc, buffer, length); + return crc32c(crc, buffer, length); } -static inline __be32 sctp_start_cksum(__u8 *buffer, __u16 length) +static inline __u32 sctp_start_cksum(__u8 *buffer, __u16 length) { - __be32 crc = ~cpu_to_be32(0); + __u32 crc = ~(__u32)0; __u8 zero[sizeof(__u32)] = {0}; /* Optimize this routine to be SCTP specific, knowing how @@ -72,12 +72,12 @@ static inline __be32 sctp_start_cksum(__u8 *buffer, __u16 length) return crc; } -static inline __be32 sctp_update_cksum(__u8 *buffer, __u16 length, __be32 crc32) +static inline __u32 sctp_update_cksum(__u8 *buffer, __u16 length, __u32 crc32) { return sctp_crc32c(crc32, buffer, length); } -static inline __be32 sctp_end_cksum(__be32 crc32) +static inline __le32 sctp_end_cksum(__be32 crc32) { - return (__force __be32)~cpu_to_le32((__force u32)crc32); + return cpu_to_le32(~crc32); } diff --git a/include/net/sctp/sctp.h b/include/net/sctp/sctp.h index bbb7742195b0..9e226be3be69 100644 --- a/include/net/sctp/sctp.h +++ b/include/net/sctp/sctp.h @@ -138,6 +138,8 @@ void sctp_write_space(struct sock *sk); unsigned int sctp_poll(struct file *file, struct socket *sock, poll_table *wait); void sctp_sock_rfree(struct sk_buff *skb); +void sctp_copy_sock(struct sock *newsk, struct sock *sk, + struct sctp_association *asoc); extern struct percpu_counter sctp_sockets_allocated; /* diff --git a/include/net/sctp/structs.h b/include/net/sctp/structs.h index 9661d7b765f0..23f08fe1d50a 100644 --- a/include/net/sctp/structs.h +++ b/include/net/sctp/structs.h @@ -218,6 +218,10 @@ extern struct sctp_globals { /* Flag to idicate if SCTP-AUTH is enabled */ int auth_enable; + + /* Flag to indicate whether computing and verifying checksum + * is disabled. */ + int checksum_disable; } sctp_globals; #define sctp_rto_initial (sctp_globals.rto_initial) @@ -252,6 +256,7 @@ extern struct sctp_globals { #define sctp_addip_noauth (sctp_globals.addip_noauth_enable) #define sctp_prsctp_enable (sctp_globals.prsctp_enable) #define sctp_auth_enable (sctp_globals.auth_enable) +#define sctp_checksum_disable (sctp_globals.checksum_disable) /* SCTP Socket type: UDP or TCP style. */ typedef enum { @@ -905,8 +910,10 @@ struct sctp_transport { * should be set. Every time the RTT * calculation completes (i.e. the DATA chunk * is SACK'd) clear this flag. + * hb_sent : a flag that signals that we have a pending heartbeat. */ __u8 rto_pending; + __u8 hb_sent; /* Flag to track the current fast recovery state */ __u8 fast_recovery; diff --git a/include/net/sock.h b/include/net/sock.h index eefeeaf7fc46..4bb1ff9fd15b 100644 --- a/include/net/sock.h +++ b/include/net/sock.h @@ -158,7 +158,7 @@ struct sock_common { * @sk_allocation: allocation mode * @sk_sndbuf: size of send buffer in bytes * @sk_flags: %SO_LINGER (l_onoff), %SO_BROADCAST, %SO_KEEPALIVE, - * %SO_OOBINLINE settings + * %SO_OOBINLINE settings, %SO_TIMESTAMPING settings * @sk_no_check: %SO_NO_CHECK setting, wether or not checkup packets * @sk_route_caps: route capabilities (e.g. %NETIF_F_TSO) * @sk_gso_type: GSO type (e.g. %SKB_GSO_TCPV4) @@ -488,6 +488,13 @@ enum sock_flags { SOCK_RCVTSTAMPNS, /* %SO_TIMESTAMPNS setting */ SOCK_LOCALROUTE, /* route locally only, %SO_DONTROUTE setting */ SOCK_QUEUE_SHRUNK, /* write queue has been shrunk recently */ + SOCK_TIMESTAMPING_TX_HARDWARE, /* %SOF_TIMESTAMPING_TX_HARDWARE */ + SOCK_TIMESTAMPING_TX_SOFTWARE, /* %SOF_TIMESTAMPING_TX_SOFTWARE */ + SOCK_TIMESTAMPING_RX_HARDWARE, /* %SOF_TIMESTAMPING_RX_HARDWARE */ + SOCK_TIMESTAMPING_RX_SOFTWARE, /* %SOF_TIMESTAMPING_RX_SOFTWARE */ + SOCK_TIMESTAMPING_SOFTWARE, /* %SOF_TIMESTAMPING_SOFTWARE */ + SOCK_TIMESTAMPING_RAW_HARDWARE, /* %SOF_TIMESTAMPING_RAW_HARDWARE */ + SOCK_TIMESTAMPING_SYS_HARDWARE, /* %SOF_TIMESTAMPING_SYS_HARDWARE */ }; static inline void sock_copy_flags(struct sock *nsk, struct sock *osk) @@ -944,6 +951,11 @@ extern struct sk_buff *sock_alloc_send_skb(struct sock *sk, unsigned long size, int noblock, int *errcode); +extern struct sk_buff *sock_alloc_send_pskb(struct sock *sk, + unsigned long header_len, + unsigned long data_len, + int noblock, + int *errcode); extern void *sock_kmalloc(struct sock *sk, int size, gfp_t priority); extern void sock_kfree_s(struct sock *sk, void *mem, int size); @@ -1340,14 +1352,45 @@ static __inline__ void sock_recv_timestamp(struct msghdr *msg, struct sock *sk, struct sk_buff *skb) { ktime_t kt = skb->tstamp; + struct skb_shared_hwtstamps *hwtstamps = skb_hwtstamps(skb); - if (sock_flag(sk, SOCK_RCVTSTAMP)) + /* + * generate control messages if + * - receive time stamping in software requested (SOCK_RCVTSTAMP + * or SOCK_TIMESTAMPING_RX_SOFTWARE) + * - software time stamp available and wanted + * (SOCK_TIMESTAMPING_SOFTWARE) + * - hardware time stamps available and wanted + * (SOCK_TIMESTAMPING_SYS_HARDWARE or + * SOCK_TIMESTAMPING_RAW_HARDWARE) + */ + if (sock_flag(sk, SOCK_RCVTSTAMP) || + sock_flag(sk, SOCK_TIMESTAMPING_RX_SOFTWARE) || + (kt.tv64 && sock_flag(sk, SOCK_TIMESTAMPING_SOFTWARE)) || + (hwtstamps->hwtstamp.tv64 && + sock_flag(sk, SOCK_TIMESTAMPING_RAW_HARDWARE)) || + (hwtstamps->syststamp.tv64 && + sock_flag(sk, SOCK_TIMESTAMPING_SYS_HARDWARE))) __sock_recv_timestamp(msg, sk, skb); else sk->sk_stamp = kt; } /** + * sock_tx_timestamp - checks whether the outgoing packet is to be time stamped + * @msg: outgoing packet + * @sk: socket sending this packet + * @shtx: filled with instructions for time stamping + * + * Currently only depends on SOCK_TIMESTAMPING* flags. Returns error code if + * parameters are invalid. + */ +extern int sock_tx_timestamp(struct msghdr *msg, + struct sock *sk, + union skb_shared_tx *shtx); + + +/** * sk_eat_skb - Release a skb if it is no longer needed * @sk: socket to eat this skb from * @skb: socket buffer to eat @@ -1415,7 +1458,7 @@ static inline struct sock *skb_steal_sock(struct sk_buff *skb) return NULL; } -extern void sock_enable_timestamp(struct sock *sk); +extern void sock_enable_timestamp(struct sock *sk, int flag); extern int sock_get_timestamp(struct sock *, struct timeval __user *); extern int sock_get_timestampns(struct sock *, struct timespec __user *); diff --git a/include/net/transp_v6.h b/include/net/transp_v6.h index 876b6f2bb4fd..bfb240c6cf79 100644 --- a/include/net/transp_v6.h +++ b/include/net/transp_v6.h @@ -46,7 +46,7 @@ extern int datagram_send_ctl(struct net *net, struct ipv6_txoptions *opt, int *hlimit, int *tclass); -#define LOOPBACK4_IPV6 __constant_htonl(0x7f000006) +#define LOOPBACK4_IPV6 cpu_to_be32(0x7f000006) /* * address family specific functions diff --git a/include/net/wireless.h b/include/net/wireless.h index 21c5d966142d..1c6285eb1666 100644 --- a/include/net/wireless.h +++ b/include/net/wireless.h @@ -181,12 +181,25 @@ struct ieee80211_supported_band { * struct wiphy - wireless hardware description * @idx: the wiphy index assigned to this item * @class_dev: the class device representing /sys/class/ieee80211/<wiphy-name> - * @fw_handles_regulatory: tells us the firmware for this device - * has its own regulatory solution and cannot identify the + * @custom_regulatory: tells us the driver for this device + * has its own custom regulatory domain and cannot identify the * ISO / IEC 3166 alpha2 it belongs to. When this is enabled * we will disregard the first regulatory hint (when the * initiator is %REGDOM_SET_BY_CORE). + * @strict_regulatory: tells us the driver for this device will ignore + * regulatory domain settings until it gets its own regulatory domain + * via its regulatory_hint(). After its gets its own regulatory domain + * it will only allow further regulatory domain settings to further + * enhance compliance. For example if channel 13 and 14 are disabled + * by this regulatory domain no user regulatory domain can enable these + * channels at a later time. This can be used for devices which do not + * have calibration information gauranteed for frequencies or settings + * outside of its regulatory domain. * @reg_notifier: the driver's regulatory notification callback + * @regd: the driver's regulatory domain, if one was requested via + * the regulatory_hint() API. This can be used by the driver + * on the reg_notifier() if it chooses to ignore future + * regulatory domain changes caused by other drivers. */ struct wiphy { /* assign these fields before you register the wiphy */ @@ -197,7 +210,11 @@ struct wiphy { /* Supported interface modes, OR together BIT(NL80211_IFTYPE_...) */ u16 interface_modes; - bool fw_handles_regulatory; + bool custom_regulatory; + bool strict_regulatory; + + int bss_priv_size; + u8 max_scan_ssids; /* If multiple wiphys are registered and you're handed e.g. * a regular netdev with assigned ieee80211_ptr, you won't @@ -209,10 +226,13 @@ struct wiphy { struct ieee80211_supported_band *bands[IEEE80211_NUM_BANDS]; /* Lets us get back the wiphy on the callback */ - int (*reg_notifier)(struct wiphy *wiphy, enum reg_set_by setby); + int (*reg_notifier)(struct wiphy *wiphy, + struct regulatory_request *request); /* fields below are read-only, assigned by cfg80211 */ + const struct ieee80211_regdomain *regd; + /* the item in /sys/class/ieee80211/ points to this, * you need use set_wiphy_dev() (see below) */ struct device dev; @@ -361,7 +381,7 @@ ieee80211_get_channel(struct wiphy *wiphy, int freq) */ struct ieee80211_rate * ieee80211_get_response_rate(struct ieee80211_supported_band *sband, - u64 basic_rates, int bitrate); + u32 basic_rates, int bitrate); /** * regulatory_hint - driver hint to the wireless core a regulatory domain @@ -395,4 +415,45 @@ extern void regulatory_hint(struct wiphy *wiphy, const char *alpha2); extern void regulatory_hint_11d(struct wiphy *wiphy, u8 *country_ie, u8 country_ie_len); + +/** + * wiphy_apply_custom_regulatory - apply a custom driver regulatory domain + * @wiphy: the wireless device we want to process the regulatory domain on + * @regd: the custom regulatory domain to use for this wiphy + * + * Drivers can sometimes have custom regulatory domains which do not apply + * to a specific country. Drivers can use this to apply such custom regulatory + * domains. This routine must be called prior to wiphy registration. The + * custom regulatory domain will be trusted completely and as such previous + * default channel settings will be disregarded. If no rule is found for a + * channel on the regulatory domain the channel will be disabled. + */ +extern void wiphy_apply_custom_regulatory( + struct wiphy *wiphy, + const struct ieee80211_regdomain *regd); + +/** + * freq_reg_info - get regulatory information for the given frequency + * @wiphy: the wiphy for which we want to process this rule for + * @center_freq: Frequency in KHz for which we want regulatory information for + * @bandwidth: the bandwidth requirement you have in KHz, if you do not have one + * you can set this to 0. If this frequency is allowed we then set + * this value to the maximum allowed bandwidth. + * @reg_rule: the regulatory rule which we have for this frequency + * + * Use this function to get the regulatory rule for a specific frequency on + * a given wireless device. If the device has a specific regulatory domain + * it wants to follow we respect that unless a country IE has been received + * and processed already. + * + * Returns 0 if it was able to find a valid regulatory rule which does + * apply to the given center_freq otherwise it returns non-zero. It will + * also return -ERANGE if we determine the given center_freq does not even have + * a regulatory rule for a frequency range in the center_freq's band. See + * freq_in_rule_band() for our current definition of a band -- this is purely + * subjective and right now its 802.11 specific. + */ +extern int freq_reg_info(struct wiphy *wiphy, u32 center_freq, u32 *bandwidth, + const struct ieee80211_reg_rule **reg_rule); + #endif /* __NET_WIRELESS_H */ |