| Commit message (Collapse) | Author | Age |
|---|
| |
|
|
|
|
|
|
|
|
|
| |
As a part of driver consolidation, move GPIO-related IRQ code to
drivers/gpio/gpio-sa1100.c. The code does not use GPIOLIB_IRQCHIP (yet),
because sa1100 does not have a device for gpios, which is a requirement
for GPIOLIB_IRQCHIP. This will be the next step.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Low GPIO pins use an interrupt in SC interrupts space. However it's
possible to handle them as if all the GPIO interrupts are instead tied
to single GPIO handler, which later decodes GEDR register and
chain-calls next IRQ handler. So split first 11 interrupts into system
part (IRQ_GPIO0_SC - IRQ_GPIO10_SC) which work exactly like the rest of
system controller interrupts and real GPIO interrupts
(IRQ_GPIO0..IRQ_GPIO10). A single handler sa1100_gpio_handler then
decodes and calls next handler.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The SA1100 was implementing its own variants of gpio_get_value()
and gpio_set_value() and only selectively falling back to
gpiolib for extended (EGPIO) handling. However the driver in
gpio/gpio-sa1100.c already handles the same functionality for
these lines, yet remain unused.
The only upside would be things like a timing-critical hotpath
on bit-banged GPIO, but that kind of things does not seem to
happen on these GPIOs, so it is not worth having the extra
complexity.
Tested with some buttons on the Compaq iPAQ H3630.
Cc: Kristoffer Ericson <kristoffer.ericson@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
| |
|
|
|
|
|
|
| |
In preparation to convert SA1100 to sparse irq, set .nr_irqs for each machine
and explicitly include mach/irqs.h as needed.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
| |
|
|
|
|
|
|
|
|
|
|
|
| |
The existing gpio_to_irq() implementation on sa1100 only translates
validly for internal GPIOs. Since this sub-arch enables GPIOLIB
support, this results in buggy translations for non-internal GPIOs.
Get rid of the private gpio_to_irq() implementation, replacing it
with the .to_irq method in the sa1100 gpio chip instead.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
|
As per example from the other ARM boards, push the SA100
GPIO driver down to the GPIO subsystem so it can be consolidated.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
