From abcc3eb00e10af3a0c5df90ce515ebde5fc12319 Mon Sep 17 00:00:00 2001 From: Benjamin Herrenschmidt Date: Tue, 18 Apr 2017 08:37:03 +1000 Subject: ftgmac100: Allow configuration of phy interface via device-tree This uses the standard phy-mode property Signed-off-by: Benjamin Herrenschmidt Signed-off-by: David S. Miller --- drivers/net/ethernet/faraday/ftgmac100.c | 42 +++++++++++++++++++++++++++++--- 1 file changed, 39 insertions(+), 3 deletions(-) (limited to 'drivers/net/ethernet/faraday') diff --git a/drivers/net/ethernet/faraday/ftgmac100.c b/drivers/net/ethernet/faraday/ftgmac100.c index f76765e0b243..7721c2ab24ef 100644 --- a/drivers/net/ethernet/faraday/ftgmac100.c +++ b/drivers/net/ethernet/faraday/ftgmac100.c @@ -34,6 +34,7 @@ #include #include #include +#include #include #include @@ -1051,7 +1052,7 @@ static void ftgmac100_adjust_link(struct net_device *netdev) schedule_work(&priv->reset_task); } -static int ftgmac100_mii_probe(struct ftgmac100 *priv) +static int ftgmac100_mii_probe(struct ftgmac100 *priv, phy_interface_t intf) { struct net_device *netdev = priv->netdev; struct phy_device *phydev; @@ -1063,7 +1064,7 @@ static int ftgmac100_mii_probe(struct ftgmac100 *priv) } phydev = phy_connect(netdev, phydev_name(phydev), - &ftgmac100_adjust_link, PHY_INTERFACE_MODE_GMII); + &ftgmac100_adjust_link, intf); if (IS_ERR(phydev)) { netdev_err(netdev, "%s: Could not attach to PHY\n", netdev->name); @@ -1618,6 +1619,8 @@ static int ftgmac100_setup_mdio(struct net_device *netdev) { struct ftgmac100 *priv = netdev_priv(netdev); struct platform_device *pdev = to_platform_device(priv->dev); + int phy_intf = PHY_INTERFACE_MODE_RGMII; + struct device_node *np = pdev->dev.of_node; int i, err = 0; u32 reg; @@ -1633,6 +1636,39 @@ static int ftgmac100_setup_mdio(struct net_device *netdev) iowrite32(reg, priv->base + FTGMAC100_OFFSET_REVR); }; + /* Get PHY mode from device-tree */ + if (np) { + /* Default to RGMII. It's a gigabit part after all */ + phy_intf = of_get_phy_mode(np); + if (phy_intf < 0) + phy_intf = PHY_INTERFACE_MODE_RGMII; + + /* Aspeed only supports these. I don't know about other IP + * block vendors so I'm going to just let them through for + * now. Note that this is only a warning if for some obscure + * reason the DT really means to lie about it or it's a newer + * part we don't know about. + * + * On the Aspeed SoC there are additionally straps and SCU + * control bits that could tell us what the interface is + * (or allow us to configure it while the IP block is held + * in reset). For now I chose to keep this driver away from + * those SoC specific bits and assume the device-tree is + * right and the SCU has been configured properly by pinmux + * or the firmware. + */ + if (priv->is_aspeed && + phy_intf != PHY_INTERFACE_MODE_RMII && + phy_intf != PHY_INTERFACE_MODE_RGMII && + phy_intf != PHY_INTERFACE_MODE_RGMII_ID && + phy_intf != PHY_INTERFACE_MODE_RGMII_RXID && + phy_intf != PHY_INTERFACE_MODE_RGMII_TXID) { + netdev_warn(netdev, + "Unsupported PHY mode %s !\n", + phy_modes(phy_intf)); + } + } + priv->mii_bus->name = "ftgmac100_mdio"; snprintf(priv->mii_bus->id, MII_BUS_ID_SIZE, "%s-%d", pdev->name, pdev->id); @@ -1649,7 +1685,7 @@ static int ftgmac100_setup_mdio(struct net_device *netdev) goto err_register_mdiobus; } - err = ftgmac100_mii_probe(priv); + err = ftgmac100_mii_probe(priv, phy_intf); if (err) { dev_err(priv->dev, "MII Probe failed!\n"); goto err_mii_probe; -- cgit v1.2.1