diff options
Diffstat (limited to 'Documentation/devicetree')
3 files changed, 79 insertions, 38 deletions
diff --git a/Documentation/devicetree/bindings/powerpc/4xx/emac.txt b/Documentation/devicetree/bindings/powerpc/4xx/emac.txt index 712baf6c3e24..44b842b6ca15 100644 --- a/Documentation/devicetree/bindings/powerpc/4xx/emac.txt +++ b/Documentation/devicetree/bindings/powerpc/4xx/emac.txt @@ -71,6 +71,9 @@ For Axon it can be absent, though my current driver doesn't handle phy-address yet so for now, keep 0x00ffffff in it. + - phy-handle : Used to describe configurations where a external PHY + is used. Please refer to: + Documentation/devicetree/bindings/net/ethernet.txt - rx-fifo-size-gige : 1 cell, Rx fifo size in bytes for 1000 Mb/sec operations (if absent the value is the same as rx-fifo-size). For Axon, either absent or 2048. @@ -81,8 +84,22 @@ offload, phandle of the TAH device node. - tah-channel : 1 cell, optional. If appropriate, channel used on the TAH engine. + - fixed-link : Fixed-link subnode describing a link to a non-MDIO + managed entity. See + Documentation/devicetree/bindings/net/fixed-link.txt + for details. + - mdio subnode : When the EMAC has a phy connected to its local + mdio, which us supported by the kernel's network + PHY library in drivers/net/phy, there must be device + tree subnode with the following required properties: + - #address-cells: Must be <1>. + - #size-cells: Must be <0>. - Example: + For PHY definitions: Please refer to + Documentation/devicetree/bindings/net/phy.txt and + Documentation/devicetree/bindings/net/ethernet.txt + + Examples: EMAC0: ethernet@40000800 { device_type = "network"; @@ -104,6 +121,48 @@ zmii-channel = <0>; }; + EMAC1: ethernet@ef600c00 { + device_type = "network"; + compatible = "ibm,emac-apm821xx", "ibm,emac4sync"; + interrupt-parent = <&EMAC1>; + interrupts = <0 1>; + #interrupt-cells = <1>; + #address-cells = <0>; + #size-cells = <0>; + interrupt-map = <0 &UIC2 0x10 IRQ_TYPE_LEVEL_HIGH /* Status */ + 1 &UIC2 0x14 IRQ_TYPE_LEVEL_HIGH /* Wake */>; + reg = <0xef600c00 0x000000c4>; + local-mac-address = [000000000000]; /* Filled in by U-Boot */ + mal-device = <&MAL0>; + mal-tx-channel = <0>; + mal-rx-channel = <0>; + cell-index = <0>; + max-frame-size = <9000>; + rx-fifo-size = <16384>; + tx-fifo-size = <2048>; + fifo-entry-size = <10>; + phy-mode = "rgmii"; + phy-handle = <&phy0>; + phy-map = <0x00000000>; + rgmii-device = <&RGMII0>; + rgmii-channel = <0>; + tah-device = <&TAH0>; + tah-channel = <0>; + has-inverted-stacr-oc; + has-new-stacr-staopc; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + phy0: ethernet-phy@0 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <0>; + }; + }; + }; + + ii) McMAL node Required properties: @@ -145,4 +204,3 @@ - revision : as provided by the RGMII new version register if available. For Axon: 0x0000012a - diff --git a/Documentation/devicetree/bindings/regulator/ti-abb-regulator.txt b/Documentation/devicetree/bindings/regulator/ti-abb-regulator.txt index c3f6546ebac7..6a23ad9ac53a 100644 --- a/Documentation/devicetree/bindings/regulator/ti-abb-regulator.txt +++ b/Documentation/devicetree/bindings/regulator/ti-abb-regulator.txt @@ -45,7 +45,7 @@ Required Properties: Optional Properties: - reg-names: In addition to the required properties, the following are optional - "efuse-address" - Contains efuse base address used to pick up ABB info. - - "ldo-address" - Contains address of ABB LDO overide register address. + - "ldo-address" - Contains address of ABB LDO override register. "efuse-address" is required for this. - ti,ldovbb-vset-mask - Required if ldo-address is set, mask for LDO override register to provide override vset value. diff --git a/Documentation/devicetree/bindings/usb/usb251xb.txt b/Documentation/devicetree/bindings/usb/usb251xb.txt index 0c065f77658f..3957d4edaa74 100644 --- a/Documentation/devicetree/bindings/usb/usb251xb.txt +++ b/Documentation/devicetree/bindings/usb/usb251xb.txt @@ -7,18 +7,18 @@ Required properties : - compatible : Should be "microchip,usb251xb" or one of the specific types: "microchip,usb2512b", "microchip,usb2512bi", "microchip,usb2513b", "microchip,usb2513bi", "microchip,usb2514b", "microchip,usb2514bi" - - hub-reset-gpios : Should specify the gpio for hub reset + - reset-gpios : Should specify the gpio for hub reset + - reg : I2C address on the selected bus (default is <0x2C>) Optional properties : - - reg : I2C address on the selected bus (default is <0x2C>) - skip-config : Skip Hub configuration, but only send the USB-Attach command - - vendor-id : USB Vendor ID of the hub (16 bit, default is 0x0424) - - product-id : USB Product ID of the hub (16 bit, default depends on type) - - device-id : USB Device ID of the hub (16 bit, default is 0x0bb3) - - language-id : USB Language ID (16 bit, default is 0x0000) - - manufacturer : USB Manufacturer string (max 31 characters long) - - product : USB Product string (max 31 characters long) - - serial : USB Serial string (max 31 characters long) + - vendor-id : Set USB Vendor ID of the hub (16 bit, default is 0x0424) + - product-id : Set USB Product ID of the hub (16 bit, default depends on type) + - device-id : Set USB Device ID of the hub (16 bit, default is 0x0bb3) + - language-id : Set USB Language ID (16 bit, default is 0x0000) + - manufacturer : Set USB Manufacturer string (max 31 characters long) + - product : Set USB Product string (max 31 characters long) + - serial : Set USB Serial string (max 31 characters long) - {bus,self}-powered : selects between self- and bus-powered operation (default is self-powered) - disable-hi-speed : disable USB Hi-Speed support @@ -31,8 +31,10 @@ Optional properties : (default is individual) - dynamic-power-switching : enable auto-switching from self- to bus-powered operation if the local power source is removed or unavailable - - oc-delay-{100us,4ms,8ms,16ms} : set over current timer delay (default is 8ms) - - compound-device : indicated the hub is part of a compound device + - oc-delay-us : Delay time (in microseconds) for filtering the over-current + sense inputs. Valid values are 100, 4000, 8000 (default) and 16000. If + an invalid value is given, the default is used instead. + - compound-device : indicate the hub is part of a compound device - port-mapping-mode : enable port mapping mode - string-support : enable string descriptor support (required for manufacturer, product and serial string configuration) @@ -40,34 +42,15 @@ Optional properties : device connected. - sp-disabled-ports : Specifies the ports which will be self-power disabled - bp-disabled-ports : Specifies the ports which will be bus-power disabled - - max-sp-power : Specifies the maximum current the hub consumes from an - upstream port when operating as self-powered hub including the power - consumption of a permanently attached peripheral if the hub is - configured as a compound device. The value is given in mA in a 0 - 500 - range (default is 2). - - max-bp-power : Specifies the maximum current the hub consumes from an - upstream port when operating as bus-powered hub including the power - consumption of a permanently attached peripheral if the hub is - configured as a compound device. The value is given in mA in a 0 - 500 - range (default is 100). - - max-sp-current : Specifies the maximum current the hub consumes from an - upstream port when operating as self-powered hub EXCLUDING the power - consumption of a permanently attached peripheral if the hub is - configured as a compound device. The value is given in mA in a 0 - 500 - range (default is 2). - - max-bp-current : Specifies the maximum current the hub consumes from an - upstream port when operating as bus-powered hub EXCLUDING the power - consumption of a permanently attached peripheral if the hub is - configured as a compound device. The value is given in mA in a 0 - 500 - range (default is 100). - - power-on-time : Specifies the time it takes from the time the host initiates - the power-on sequence to a port until the port has adequate power. The - value is given in ms in a 0 - 510 range (default is 100ms). + - power-on-time-ms : Specifies the time it takes from the time the host + initiates the power-on sequence to a port until the port has adequate + power. The value is given in ms in a 0 - 510 range (default is 100ms). Examples: usb2512b@2c { compatible = "microchip,usb2512b"; - hub-reset-gpios = <&gpio1 4 GPIO_ACTIVE_LOW>; + reg = <0x2c>; + reset-gpios = <&gpio1 4 GPIO_ACTIVE_LOW>; }; usb2514b@2c { |