| Commit message (Collapse) | Author | Age |
|---|
| |\
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Pull networking fixes from David Miller:
1) Fix rtnl deadlock in ipvs, from Julian Anastasov.
2) s390 qeth fixes from Julian Wiedmann (control IO completion stalls,
bad MAC address update sequence, request side races on command IO
timeouts).
3) Handle seq_file overflow properly in l2tp, from Guillaume Nault.
4) Fix VLAN priority mappings in cpsw driver, from Ivan Khoronzhuk.
5) Packet scheduler ife action fixes (malformed TLV lengths, etc.) from
Alexander Aring.
6) Fix out of bounds access in tcp md5 option parser, from Jann Horn.
7) Missing netlink attribute policies in rtm_ipv6_policy table, from
Eric Dumazet.
8) Missing socket address length checks in l2tp and pppoe connect, from
Guillaume Nault.
9) Fix netconsole over team and bonding, from Xin Long.
10) Fix race with AF_PACKET socket state bitfields, from Willem de
Bruijn.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (51 commits)
ice: Fix insufficient memory issue in ice_aq_manage_mac_read
sfc: ARFS filter IDs
net: ethtool: Add missing kernel doc for FEC parameters
packet: fix bitfield update race
ice: Do not check INTEVENT bit for OICR interrupts
ice: Fix incorrect comment for action type
ice: Fix initialization for num_nodes_added
igb: Fix the transmission mode of queue 0 for Qav mode
ixgbevf: ensure xdp_ring resources are free'd on error exit
team: fix netconsole setup over team
amd-xgbe: Only use the SFP supported transceiver signals
amd-xgbe: Improve KR auto-negotiation and training
amd-xgbe: Add pre/post auto-negotiation phy hooks
pppoe: check sockaddr length in pppoe_connect()
l2tp: check sockaddr length in pppol2tp_connect()
net: phy: marvell: clear wol event before setting it
ipv6: add RTA_TABLE and RTA_PREFSRC to rtm_ipv6_policy
bonding: do not set slave_dev npinfo before slave_enable_netpoll in bond_enslave
tcp: don't read out-of-bounds opsize
ibmvnic: Clean actual number of RX or TX pools
...
|
| | |\
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Daniel Borkmann says:
====================
pull-request: bpf 2018-04-21
The following pull-request contains BPF updates for your *net* tree.
The main changes are:
1) Fix a deadlock between mm->mmap_sem and bpf_event_mutex when
one task is detaching a BPF prog via perf_event_detach_bpf_prog()
and another one dumping through bpf_prog_array_copy_info(). For
the latter we move the copy_to_user() out of the bpf_event_mutex
lock to fix it, from Yonghong.
2) Fix test_sock and test_sock_addr.sh failures. The former was
hitting rlimit issues and the latter required ping to specify
the address family, from Yonghong.
3) Remove a dead check in sockmap's sock_map_alloc(), from Jann.
4) Add generated files to BPF kselftests gitignore that were previously
missed, from Anders.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
The bpf selftests test_sock and test_sock_addr.sh failed
in my test machine. The failure looks like:
$ ./test_sock
Test case: bind4 load with invalid access: src_ip6 .. [PASS]
Test case: bind4 load with invalid access: mark .. [PASS]
Test case: bind6 load with invalid access: src_ip4 .. [PASS]
Test case: sock_create load with invalid access: src_port .. [PASS]
Test case: sock_create load w/o expected_attach_type (compat mode) .. [FAIL]
Test case: sock_create load w/ expected_attach_type .. [FAIL]
Test case: attach type mismatch bind4 vs bind6 .. [FAIL]
...
Summary: 4 PASSED, 12 FAILED
$ ./test_sock_addr.sh
Wait for testing IPv4/IPv6 to become available .....
ERROR: Timeout waiting for test IP to become available.
In test_sock, bpf program loads failed due to hitting memlock limits.
In test_sock_addr.sh, my test machine is a ipv6 only test box and using
"ping" without specifying address family for an ipv6 address does not work.
This patch fixed the issue by including header bpf_rlimit.h in test_sock.c
and test_sock_addr.c, and specifying address family for ping command.
Cc: Andrey Ignatov <rdna@fb.com>
Signed-off-by: Yonghong Song <yhs@fb.com>
Acked-by: Andrey Ignatov <rdna@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
| | | |
| | |
| | |
| | |
| | | |
Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
| |\ \ \
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm
Pull libnvdimm fixes from Dan Williams:
"A regression fix, new unit test infrastructure and a build fix:
- Regression fix addressing support for the new NVDIMM label storage
area access commands (_LSI, _LSR, and _LSW).
The Intel specific version of these commands communicated the
"Device Locked" status on the label-storage-information command.
However, these new commands (standardized in ACPI 6.2) communicate
the "Device Locked" status on the label-storage-read command, and
the driver was missing the indication.
Reading from locked persistent memory is similar to reading
unmapped PCI memory space, returns all 1's.
- Unit test infrastructure is added to regression test the "Device
Locked" detection failure.
- A build fix is included to allow the "of_pmem" driver to be built
as a module and translate an Open Firmware described device to its
local numa node"
* 'libnvdimm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
MAINTAINERS: Add backup maintainers for libnvdimm and DAX
device-dax: allow MAP_SYNC to succeed
Revert "libnvdimm, of_pmem: workaround OF_NUMA=n build error"
libnvdimm, of_pmem: use dev_to_node() instead of of_node_to_nid()
tools/testing/nvdimm: enable labels for nfit_test.1 dimms
tools/testing/nvdimm: fix missing newline in nfit_test_dimm 'handle' attribute
tools/testing/nvdimm: support nfit_test_dimm attributes under nfit_test.1
tools/testing/nvdimm: allow custom error code injection
libnvdimm, dimm: handle EACCES failures from label reads
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Enable test cases for the kernel's fallback to label-less mode.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Sysfs userspace tooling generally expects the kernel to emit a newlines
when reading sysfs attributes.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
The nfit_test.1 bus provides a pmem topology without blk-aperture
enabling, so it presents different failure modes for label space
handling. Allow custom DSM command error injection.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Given that libnvdimm driver stack takes specific actions on DIMM command
error codes like -EACCES, provide a facility to inject custom failures.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
| |\ \ \ \
| |_|/ /
|/| | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest
Pull Kselftest fix from Shuah Khan:
"A fix from Michael Ellerman to not run dnotify_test by default to
prevent Kselftest running forever"
* tag 'linux-kselftest-4.17-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest:
selftests/filesystems: Don't run dnotify_test by default
|
| | |/ /
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
In commit ce290a19609d ("selftests: add devpts selftests"), the
filesystems directory was added to the top-level selftests Makefile.
That had the effect of causing the existing dnotify_test in the
filesystems directory to now be run as part of the default selftests
test-run. Unfortunately dnotify_test is actually an infinite loop.
Fix it by moving dnotify_test to TEST_GEN_PROGS_EXTENDED, which says
that it's a generated file (ie. built) but should not be run as part
of the default test suite run (it's an "extended" test).
While we're here cleanup a few other things, devpts_pts should be in
TEST_GEN_PROGS to indicate that it's built, and with the above two
changes we no longer need a custom all or clean rule.
Fixes: ce290a19609d ("selftests: add devpts selftests")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Acked-by: Christian brauner <christian.brauner@ubuntu.com>
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
|
| |\ \ \
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Pull networking fixes from David Miller:
1) Unbalanced refcounting in TIPC, from Jon Maloy.
2) Only allow TCP_MD5SIG to be set on sockets in close or listen state.
Once the connection is established it makes no sense to change this.
From Eric Dumazet.
3) Missing attribute validation in neigh_dump_table(), also from Eric
Dumazet.
4) Fix address comparisons in SCTP, from Xin Long.
5) Neigh proxy table clearing can deadlock, from Wolfgang Bumiller.
6) Fix tunnel refcounting in l2tp, from Guillaume Nault.
7) Fix double list insert in team driver, from Paolo Abeni.
8) af_vsock.ko module was accidently made unremovable, from Stefan
Hajnoczi.
9) Fix reference to freed llc_sap object in llc stack, from Cong Wang.
10) Don't assume netdevice struct is DMA'able memory in virtio_net
driver, from Michael S. Tsirkin.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (62 commits)
net/smc: fix shutdown in state SMC_LISTEN
bnxt_en: Fix memory fault in bnxt_ethtool_init()
virtio_net: sparse annotation fix
virtio_net: fix adding vids on big-endian
virtio_net: split out ctrl buffer
net: hns: Avoid action name truncation
docs: ip-sysctl.txt: fix name of some ipv6 variables
vmxnet3: fix incorrect dereference when rxvlan is disabled
llc: hold llc_sap before release_sock()
MAINTAINERS: Direct networking documentation changes to netdev
atm: iphase: fix spelling mistake: "Tansmit" -> "Transmit"
net: qmi_wwan: add Wistron Neweb D19Q1
net: caif: fix spelling mistake "UKNOWN" -> "UNKNOWN"
net: stmmac: Disable ACS Feature for GMAC >= 4
net: mvpp2: Fix DMA address mask size
net: change the comment of dev_mc_init
net: qualcomm: rmnet: Fix warning seen with fill_info
tun: fix vlan packet truncation
tipc: fix infinite loop when dumping link monitor summary
tipc: fix use-after-free in tipc_nametbl_stop
...
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Script in_netns.sh isn't installed.
--------------------
running psock_fanout test
--------------------
./run_afpackettests: line 12: ./in_netns.sh: No such file or directory
[FAIL]
--------------------
running psock_tpacket test
--------------------
./run_afpackettests: line 22: ./in_netns.sh: No such file or directory
[FAIL]
In current code added in_netns.sh to be installed.
Fixes: cc30c93fa020 ("selftests/net: ignore background traffic in psock_fanout")
Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| |\ \ \ \
| |_|/ /
|/| | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Pull kvm fixes from Paolo Bonzini:
"Bug fixes, plus a new test case and the associated infrastructure for
writing nested virtualization tests"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
kvm: selftests: add vmx_tsc_adjust_test
kvm: x86: move MSR_IA32_TSC handling to x86.c
X86/KVM: Properly update 'tsc_offset' to represent the running guest
kvm: selftests: add -std=gnu99 cflags
x86: Add check for APIC access address for vmentry of L2 guests
KVM: X86: fix incorrect reference of trace_kvm_pi_irte_update
X86/KVM: Do not allow DISABLE_EXITS_MWAIT when LAPIC ARAT is not available
kvm: selftests: fix spelling mistake: "divisable" and "divisible"
X86/VMX: Disable VMX preemption timer if MWAIT is not intercepted
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
The test checks the behavior of setting MSR_IA32_TSC in a nested guest,
and the TSC_OFFSET VMCS field in general. It also introduces the testing
infrastructure for Intel nested virtualization.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
lib/kvm_util.c: In function ‘kvm_memcmp_hva_gva’:
lib/kvm_util.c:332:2: error: ‘for’ loop initial declarations are only allowed in C99 mode
So add -std=gnu99 to CFLAGS
Signed-off-by: Peng Hao <peng.hao2@zte.com.cn>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Trivial fix to spelling mistakes in comment and message text
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
| | |/ /
|/| |
| | |
| | |
| | |
| | |
| | | |
Add copyright in two files before they get autorubberstamped.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
| |\ \ \
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-ktest
Pull ktest updates from Steven Rostedt:
"These commits have either been sitting in my INBOX or have been in my
local tree for some time. I need to push them upstream:
- Separate out config-bisect.pl from ktest.pl.
This allows users to do config bisects without full ktest setup.
- Email on status change.
Allow the user to be emailed on test start, finish, failure, etc.
- Other small fixes and enhancements"
* tag 'ktest-v4.17' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-ktest: (24 commits)
ktest: Take submenu into account for grub2 menus
ktest.pl: Add MAIL_COMMAND option to define how to send email
ktest.pl: Use run_command to execute sending mail
ktest.pl: Allow dodie be recursive
ktest.pl: Kill test if mailer is not supported
ktest.pl: Add MAIL_PATH option to define where to find the mailer
ktest.pl: No need to print no mailer is specified when mailto is not
Ktest: add email options to sample.config
Ktest: Use dodie for critical falures
Ktest: Add SigInt handling
Ktest: Add email support
ktest.pl: Detect if a config-bisect was interrupted
ktest.pl: Make finding config-bisect.pl dynamic
ktest.pl: Have ktest.pl pass -r to config-bisect.pl to reset bisect
ktest.pl: Use diffconfig if available for failed config bisects
ktest.pl: Allow for the config-bisect.pl output to display to console
ktest: Use config-bisect.pl in ktest.pl
ktest: Add standalone config-bisect.pl program
ktest: Set do_not_reboot=y for CONFIG_BISECT_TYPE=build
ktest: Set buildonly=1 for CONFIG_BISECT_TYPE=build
...
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
grub-reboot selects the submenu's first menuentry (title is "1>0") rather than ktest's
menuentry (title is "2") by mistake.
===
$ sudo cat /boot/grub/grub.cfg | grep -E "^menuentry|^submenu"
...
menuentry 'Ubuntu' --class ubuntu --class gnu-linux --class gnu --class os $menuentry_id_option '...' {
...
submenu 'Advanced options for Ubuntu' $menuentry_id_option '...' {
...
menuentry 'ktest' {
...
===
Correct it by taking submenu entries into account in get_grub2_index().
Link: http://lkml.kernel.org/r/87poaje4as.wl-satoru.takeuchi@gmail.com
Signed-off-by: Satoru Takeuchi <satoru.takeuchi@gmail.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Allow the user to override the default way to send email. This will allow
the user to add their own mailer and format for sending email.
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Instead of open coding system() call, use run_command which will log the
sending of email as well.
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
If dodie cause a function that itself will call dodie, then be able to
handle that. This will allow dodie functions to call run_command, which
could possibly call dodie. If dodie is called again, simply ignore it.
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
If the user specifies a MAILTO, but the MAILER is not supported, then
kill the test.
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
The option MAIL_PATH lets the user decide how to find the mailer they are
using. For example, sendmail is usually located in /usr/sbin but is not
always in the path of non admin users. Have ktest look through the user's
PATH environment variable (adding /usr/sbin) as well, but if that's not good
enough, allow the user to define where to find the mailer.
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
squash to mail exec
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
If the user doesn't want to send mail, then don't bother them with output
that says they didn't specify a mailer. That can be annoying.
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
A block of email options is added under the optional config section.
Link: http://lkml.kernel.org/r/1522094884-22718-5-git-send-email-tianyang.chen@oracle.com
Suggested-by: Dhaval Giani <dhaval.giani@oracle.com>
Signed-off-by: Tim Tianyang Chen <tianyang.chen@oracle.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Users should get emails when the script dies because of a critical failure.
Critical failures are defined as any errors that could abnormally terminate
the script.
In order to add email support, this patch converts all die() to dodie() except:
* when '-v' is used as an option to get the version of the script.
* in Sig-Int handeler because it's not a fatal error to cancel the script.
* errors happen during parsing config
Link: http://lkml.kernel.org/r/1522094884-22718-4-git-send-email-tianyang.chen@oracle.com
Suggested-by: Dhaval Giani <dhaval.giani@oracle.com>
Signed-off-by: Tim Tianyang Chen <tianyang.chen@oracle.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
User can cancel tests and specify handler's behavior using option
'EMAIL_WHEN_CANCELED'.
Link: http://lkml.kernel.org/r/1522094884-22718-3-git-send-email-tianyang.chen@oracle.com
Suggested-by: Dhaval Giani <dhaval.giani@oracle.com>
Signed-off-by: Tim Tianyang Chen <tianyang.chen@oracle.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Users can define optional variables to get email notifications.
Ktest can send emails when the script:
* was started
* failed with fatal errors and called dodie()
* completed all testing
Users have to setup the mailer provided in config prior to using this script.
Supported mailers: mailx, mail, sendmail
mailer specific routines are _sendmail_send(), _mailx_send()
Link: http://lkml.kernel.org/r/1522094884-22718-2-git-send-email-tianyang.chen@oracle.com
Suggested-by: Dhaval Giani <dhaval.giani@oracle.com>
Signed-off-by: Tim Tianyang Chen <tianyang.chen@oracle.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
If a config-bisect was interrupted, then allow the user to continue, or
restart a new config-bisect.
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Just looking for config-bisect.pl in the source tree can be risky,
especially, if the source tree being tested doesn't have config-bisect.pl in
place. Instead, allow the user to set where to find config-bisect.pl with a
new option CONFIG_BISECT_EXEC.
If this option is not set, by default, ktest.pl will look for
config-bisect.pl in the following locations:
`pwd`/config-bisect.pl # where ktest.pl was called from
`dirname /path/to/ktest.pl`/config-bisect.pl # where ktest.pl exists
${BUILD_DIR}/tools/testing/ktest/config-bisect.pl
# where config-bisect.pl exists in the source tree.
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
If config-bisect.pl sees that a config_bisect has already been started, it
will ask on the command line if it should bisect or not. This will mess up
running config_bisect from ktest.pl.
Have ktest.pl pass in '-r' to config-bisect.pl and have config-bisect.pl
recognize that to reset without asking.
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Check to see if diffconfig is available and use that to diff the configs
instead of using 'diff -u', as diffconfig produces much better output of
kernel config files. It checks the source directory for the executable.
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
When commands are run in ktest, they are only displayed in the ktest log
file, but that is not sufficient for outputting the display for config
bisects. The result of a config bisect is not shown.
Add a way to display the output of "run_command" which is the subroutine
used by ktest to execute commands. Use this feature to display the output of
config-bisect.pl executions to see the progress as well as the result.
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Reduce code duplication and take advantage of bisection logic
improvements by calling config-bisect.pl.
The output of make oldconfig is now copied directly to the desired file,
rather than doing assign_configs+save_config, in order to preserve the
ordering so that diffing the configs at the end will provide useful
output.
Link: http://lkml.kernel.org/r/20170717001630.10518-8-swood@redhat.com
Signed-off-by: Scott Wood <swood@redhat.com>
[ Modified to use with new version of config-bisect.pl ]
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Started working on a stand alone program that can do a config bisect. It is
based on the config bisect code of ktest.pl. Instead of needing all the
infrastructure of ktest.pl, all that is required for config-bisect.pl is two
config files. One that works, and one that does not. The goal is to pass in
the two files, and it will create a new "good" and a new "bad" config file
based on input from the user. After several iterations (calls to this
program), it will eventually end with a minimum config value that allows one
config to work and the other config to break.
The program uses a technique that takes the good config and then makes half
of the configs that differ from the bad config just like the bad config.
The code will use make oldconfig to make sure the configs that are set are
not all converted back due to incorrect dependencies on other configs set in
the bad config but not in the new test config.
This is still a work in progress, but as it was written while I was working
at Red Hat, I want this code to be submitted as such.
Signed-off-by: Steven Rostedt (Red Hat) <rostedt@goodmis.org>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Currently setting do_not_reboot is triggered by simple builds and bisect
builds, but not config bisect builds.
Link: http://lkml.kernel.org/r/20170717001630.10518-3-swood@redhat.com
Signed-off-by: Scott Wood <swood@redhat.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Rather than adding a third copy of the same logic, rework it to cover
all three buildonly cases at once.
In the future, please consider using the same variable to perform the
same function regardless of context...
Link: http://lkml.kernel.org/r/20170717001630.10518-2-swood@redhat.com
Signed-off-by: Scott Wood <swood@redhat.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
ktest.pl will read any file as long as its name is specified as the first
argument on the command line. Comment this fact in sample.conf.
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Simply telling a new user to edit "the config file" without giving any
hints on where that file should go, what it should be named, or where
a template can be found, is not particularly helpful.
Link: http://lkml.kernel.org/r/20170717001630.10518-1-swood@redhat.com
Signed-off-by: Scott Wood <swood@redhat.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Before ktest issues a reboot, it will try to connect to the target machine
to make sure that it is still alive. If the target does not respond within 5
seconds, it will power cycle the box instead of issuing a reboot.
Five seconds may be too short, and ktest may unnecessarially power cycle the
box. I have found 25 seconds seems to be a better timeout for this purpose.
But even 25 may be too arbitrary. Add a CONNECT_TIMEOUT option to let the
user determine the timeout time before rebooting. By default, it has been
raised to 25 seconds.
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
To clean up the console processes that are forked to monitor the console,
there needs to be a waitpid().
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Patch series "XArray", v9. (First part thereof).
This patchset is, I believe, appropriate for merging for 4.17. It
contains the XArray implementation, to eventually replace the radix
tree, and converts the page cache to use it.
This conversion keeps the radix tree and XArray data structures in sync
at all times. That allows us to convert the page cache one function at
a time and should allow for easier bisection. Other than renaming some
elements of the structures, the data structures are fundamentally
unchanged; a radix tree walk and an XArray walk will touch the same
number of cachelines. I have changes planned to the XArray data
structure, but those will happen in future patches.
Improvements the XArray has over the radix tree:
- The radix tree provides operations like other trees do; 'insert' and
'delete'. But what most users really want is an automatically
resizing array, and so it makes more sense to give users an API that
is like an array -- 'load' and 'store'. We still have an 'insert'
operation for users that really want that semantic.
- The XArray considers locking as part of its API. This simplifies a
lot of users who formerly had to manage their own locking just for
the radix tree. It also improves code generation as we can now tell
RCU that we're holding a lock and it doesn't need to generate as much
fencing code. The other advantage is that tree nodes can be moved
(not yet implemented).
- GFP flags are now parameters to calls which may need to allocate
memory. The radix tree forced users to decide what the allocation
flags would be at creation time. It's much clearer to specify them at
allocation time.
- Memory is not preloaded; we don't tie up dozens of pages on the off
chance that the slab allocator fails. Instead, we drop the lock,
allocate a new node and retry the operation. We have to convert all
the radix tree, IDA and IDR preload users before we can realise this
benefit, but I have not yet found a user which cannot be converted.
- The XArray provides a cmpxchg operation. The radix tree forces users
to roll their own (and at least four have).
- Iterators take a 'max' parameter. That simplifies many users and will
reduce the amount of iteration done.
- Iteration can proceed backwards. We only have one user for this, but
since it's called as part of the pagefault readahead algorithm, that
seemed worth mentioning.
- RCU-protected pointers are not exposed as part of the API. There are
some fun bugs where the page cache forgets to use rcu_dereference()
in the current codebase.
- Value entries gain an extra bit compared to radix tree exceptional
entries. That gives us the extra bit we need to put huge page swap
entries in the page cache.
- Some iterators now take a 'filter' argument instead of having
separate iterators for tagged/untagged iterations.
The page cache is improved by this:
- Shorter, easier to read code
- More efficient iterations
- Reduction in size of struct address_space
- Fewer walks from the top of the data structure; the XArray API
encourages staying at the leaf node and conducting operations there.
This patch (of 8):
None of these bits may be used for slab allocations, so we can use them
as radix tree flags as long as we mask them off before passing them to
the slab allocator. Move the IDR flag from the high bits to the
GFP_ZONEMASK bits.
Link: http://lkml.kernel.org/r/20180313132639.17387-3-willy@infradead.org
Signed-off-by: Matthew Wilcox <mawilcox@microsoft.com>
Acked-by: Jeff Layton <jlayton@kernel.org>
Cc: Darrick J. Wong <darrick.wong@oracle.com>
Cc: Dave Chinner <david@fromorbit.com>
Cc: Ryusuke Konishi <konishi.ryusuke@lab.ntt.co.jp>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
The only tests I could come up with for /proc/uptime are:
- test that values increase monotonically for 1 second,
- bounce around CPUs and test the same thing.
Avoid glibc like plague for affinity given patches like this:
https://marc.info/?l=linux-kernel&m=152130031912594&w=4
Link: http://lkml.kernel.org/r/20180317165235.GB3445@avx2
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Shuah Khan <shuah@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Perform reads with nearly everything in /proc, and some writing as well.
Hopefully memleak checkers and KASAN will find something.
[adobriyan@gmail.com: /proc/kmsg can and will block if read under root]
Link: http://lkml.kernel.org/r/20180316232147.GA20146@avx2
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
[adobriyan@gmail.com: /proc/sysrq-trigger lives on the ground floor]
Link: http://lkml.kernel.org/r/20180317164911.GA3445@avx2
Link: http://lkml.kernel.org/r/20180315201251.GA12396@avx2
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Test fork counter formerly known as ->last_pid, the only part of
/proc/loadavg which can be tested.
Testing in init pid namespace is not reliable because of background
activity.
Link: http://lkml.kernel.org/r/20180311152241.GA26247@avx2
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Shuah Khan <shuah@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
I totally forgot that _parse_integer() accepts arbitrary amount of
leading zeroes leading to the following lookups:
OK
# readlink /proc/1/map_files/56427ecba000-56427eddc000
/lib/systemd/systemd
bogus
# readlink /proc/1/map_files/00000000000056427ecba000-56427eddc000
/lib/systemd/systemd
# readlink /proc/1/map_files/56427ecba000-00000000000056427eddc000
/lib/systemd/systemd
Link: http://lkml.kernel.org/r/20180303215130.GA23480@avx2
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Reviewed-by: Cyrill Gorcunov <gorcunov@gmail.com>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Pavel Emelyanov <xemul@virtuozzo.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Read from /proc/self/syscall should yield read system call and correct
args in the output as current is reading /proc/self/syscall.
Link: http://lkml.kernel.org/r/20180226212145.GB742@avx2
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Shuah Khan <shuah@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
This patch starts testing /proc. Many more tests to come (I promise).
Read from /proc/self/wchan should always return "0" as current is in
TASK_RUNNING state while reading /proc/self/wchan.
Link: http://lkml.kernel.org/r/20180226212006.GA742@avx2
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Shuah Khan <shuah@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
